HBCR-2211 Agilent(Hewlett-Packard), HBCR-2211 Datasheet
HBCR-2211
Related parts for HBCR-2211
HBCR-2211 Summary of contents
Page 1
... The HBCR-2210 series decode ICs make it easy to add this capability without the need to H HBCR-2210 HBCR-2211 invest in the development of bar code decoding software. The bar code decoder ICs are compatible with most hand held scanners and some medium speed machine mounted laser heads ...
Page 2
... This code can be scanned bi- directionally. Scanner Input The HBCR-2210 decode IC is designed to accept data from hand held digital scanners or slot readers with the following logic state: black = high, white = low. The same decode IC also accepts ...
Page 3
... The scanner type pin (SCT) on the HBCR-2210 series must be driven prior to power up or hard reset to identify the type of scanner connected. In the HBCR-2210 series ICs, the automatic laser shutoff feature delay time is adjustable as a con- figuration option ...
Page 4
... I/O interfaces • Laser input timing diagrams Table 1. Ordering Information Part Number HBCR-2210 CMOS, 40 pin DIP, bulk ship, no manual HBCR-2211 CMOS, 44 pin PLCC, bulk ship, no manual OPT A01 IC individually boxed with manual and data sheet HBCR-2297 HBCR-2210 Series Users Manual Recommended Operating Conditions ...
Page 5
... Selection Interleaved Interleaved Length variable from 4 to 32, Specific Label or a specific even length be- Length Selection tween 2 and 32, or lengths 6 and 14 only ( + 4 5 HBCR-2211 Pins Min. all all except 10 10, 20 0.7 V 2-9, 11, 13-19, 24-31 30, 32-39 33, 36-43 2-9, 11, 13-19, 24-31 ...
Page 6
Feature Check Character For Code 39 Verification Enable For Interleaved When enabled, the check character at the end of the bar code data is verified by the decoder Check Character For both Code 39 and Interleaved Transmission ...
Page 7
Feature Function or Value Header Selection A string of characters pre- pended to the decoded message (10 characters, maximum) Trailer Selection A string of characters appended to the decoded message (10 characters, maximum) Reader Address Reader Address is transmitted at ...
Page 8
Feature Laser Connection When enabled, the scanner type Detection Enable pin is ignored at powerup. Instead, the decoder tests for a laser scanner to determine scanner type Laser Trigger When enabled, the laser scanner Latch Mode Enable continues to scan ...
Page 9
... For use with laser scanning, this command causes immediate execution of Command previous commands that would otherwise be postponed until the laser scan finishes Table 4. Summary of Other Features - HBCR-2210 Series Power Idle Mode Reduces current draw of processor from approximately wand mode when the wand is inactive ...
Page 10
Parallel Mode Handshake Timing Handshake and Data Lines CDY CRD PP0-PP7 Figure 1. Host Commands Received by Decode IC (Reader). Handshake Timing t = Falling edge of command ready to falling edge of command read. Max. ...
Page 11
... Figure 3. HBCR-2210 Serial Pinout. following baking cycles. The parts must then be mounted within 48 hours. If the parts are not mounted with hours, they must be re- baked. The total number of baking cycles must not exceed two. If the ICs ...
Page 12
... LSE 7 8 SCT 9 TRG 10 RST 11 RxD TxD 14 SDI 15 SSY 16 LED 17 BPR Figure 4. HBCR-2211 Serial Pinout. CRD CDY 2 39 AD0 DWR 3 38 AD1 DDY 4 37 AD2 RTS 5 36 AD3 LSE 6 35 ...
Page 13
... TRG 10 RST 11 PGB PRD 14 SDI 15 SSY 16 LED 17 BPR Figure 6. HBCR-2211 Parallel Pinout. 52.8 51.9 40 INDEX MARK AREA 1 0.65 MAX. 2.54 ± 0.25 UNITS (mm) Figure 7. HBCR-2210 Mechanical Specifications. AD0-AD7 ADDRESS/DATA BUS DWR DATA WRITE HANDSHAKE DDY READY FOR DATA HANDSHAKE CRD ...
Page 14
... INDEX MARK 1 17.4 16 4.57 4.20 0.53 0.33 16.0 15.0 UNITS (mm) Figure 8. HBCR-2211 Mechanical Specifications. (OPT) EE PROM HBCR-2210 SERIES BAR CODE ADDRESS/ INPUT DATA Figure 9. System Block Diagram. 4- 16.0 15.0 0.81 1.32 0.66 1. 0.51 MIN. CONTROL CONTROL ADDRESS RAM ADDRESS LATCH DATA 8 PARALLEL PORT (OPT) 646 OR (2)–74HC574 DATA SERIAL ...
Page 15
Warranty and Service The HP Bar Code Decode IC is warranted for a period of one year after purchase covering defects in material and workman- ship. Hewlett-Packard will repair or, at its option, replace products that prove to be defective ...