TA1343 TOSHIBA [Toshiba Semiconductor], TA1343 Datasheet - Page 9

• Manufacturer Part Number: TA1343
• Description: TV SOUND PROCESSOR
• Manufacturer: TOSHIBA [Toshiba Semiconductor]

· ALS switch (sub address 03 (h)/b6), ALS start point (sub address 03 (h)/b5 to b4)
· Surround mode 1 (sub address 06 (h)/b6), Surround mode 2 (sub address 06 (h)/b7)
· Mute 1 (sub address 07 (h)/b0), Mute 2 (sub address 07 (h)/b1)
· Woofer LPF fo (sub address 07 (h)/b5 to b4)
· Woofer LPF defeat (sub address 07 (h)/b3)
· Bass boost switch (sub address 07 (h)/b7)
(Automatic Level Suppresser) suppresses Wch signal level under ALS start point, and reduces the
distortion in large signals input condition.
the bits to 01 (b), ALS start point is 380 mV
set the bits to 11 (b), ALS start point is 770 mV
shifted by 1 phase shift stage. Set the bit to 1 (b), L-R signal is shifted by 4 phase shift stages.
2 must be set to 0 (b). When input signal is monaural, surround mode 2 must be set to 1 (b) (pseudo stereo
mode).
(b), Mute 2 is active.
is 170 Hz. Set the bits to 11 (b), fo is 210 Hz.
without woofer output.
these components in an I
as define by Philips.
Gain of Wch is large. So output signals of Wch is distort easily when the input signals are large. ALS
Set the bit of sub address 03 (h)/b6 to 0 (b), ALS is inactive. Set the bit 1 to (b), ALS is active.
Switch on default data is 0 (b).
The bits of 03 (h)/b5 to b4 set ALS start point. Set the bits to 00 (b), ALS start point is 220 mV
Switch on default data is 00 (b).
Surround mode 1 is selection of phase shift value of the surround circuit. Set the bit to 0 (b), L-R signal is
Surround mode 2 is selected by condition of the input signal. When input signal is stereo, surround mode
Recommend setting surround 1 to 1 (b) when pseudo stereo mode is selected.
When Mute 1 is active, all outputs are muted.
Set the bit to 0 (b), mute 1 is inactive. Set the bit to 1 (b), Mute 1 is active.
Switch on default data is 0 (b).
When Mute 2 is active, only Wch output is muted. Set the bit to 0 (b), Mute 2 is inactive. Set the bit to 1
Switch on default data is 0 (b).
These bits set cut off frequency (fo) of the low pass filter for Wch.
Set the bits to 00 (b), fo is 100 Hz (-3dB point). Set the bits to 01 (b), fo is 125 Hz. Set the bits to 10 (b), fo
Switch on default data is 01 (h).
Set the bit to 1 (b), Woofer LPF is defeated.
This function is for device test. So, this bit must be set to 0 (b).
Switch on default data is 0 (b).
Bass boost function is adding Wch signal to main channel signals. It can boost low frequency signal
Set the bit 0 (b), Bass boost is inactive. Set the bit 1 (b), bass boost is active.
Switch on default data is 0 (b).
Purchase of TOSHIBA I
2
2
C system, provided that the system conforms to the I
C components conveys a license under the Philips I
rms
rms
. Set the bits to 10 (b), ALS start point is 525 mV
9
.
2
2
C Patent Rights to use
C Standard Specification
2002-02-12
TA1343N
rms
rms
. And
. Set