CXO3MHG STATEK [STATEK CORPORATION], CXO3MHG Datasheet - Page 2

• Manufacturer Part Number: CXO3MHG
• Description: High Shock, Low-Profile Miniature Surface-Mount 3.3 V Crystal Oscillator
• Manufacturer: STATEK [STATEK CORPORATION]

STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: [phone] www.statek.com
CXO3MHG
PACKAGING OPTIONS
CXO3MHG
HOW TO ORDER CXO3MHG SURFACE MOUNT CRYSTAL OSCILLATORS
SPECIFICATIONS
Specifications are typical at 25
Specifications are subject to change without notice. Tighter
specifications available. Please contact factory.
Supply Voltage
Calibration Tolerance
Frequency Stability
Over Temperature
Supply Current (Typical)
Output Load (CMOS)
Start-up Time
Rise/Fall Time
Duty Cycle
Aging, first year
Shock, survival
Vibration, survival
Operating Temp Ranges -10
1. Other voltages available. For 5.0 V, see CXOMHG data sheet. For others,
2. Other tolerances available.
3. Does not include calibration tolerance. Other tolerances available.
4. Higher CMOS loads and TTL loads available. Contact factory.
5. Higher shock version available. Contact factory for requirements above 10,000 g.
6. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also
Note: All parameters are measured at ambient temperature with a 10 M , 15 pF load.
available.
contact factory.
“S” if special or
custom design;
otherwise blank.
S
- Tray Pack
- 16 mm tape, 7˝ or 13˝ reels
5
1
6
Per EIA 418
3
4
2
Enable/Disable Option
E, T, or N
10 MHz
24 MHz
30 MHz
40 MHz
50 MHz
15 pF
3.3 V
5 ms MAX
6 ns MAX
40% MIN, 60% MAX
10 ppm MAX
10,000 g, 0.3 ms,
20 g, 10-2,000 Hz swept sine
-40
-55
+ _
+ _
+ _
+ _
100 ppm
100 ppm for Industrial
T
100 ppm for Military
50 ppm for Commercial
O
O
O
(see Tape and Reel data sheet 10109)
C to +70
C to +85
C to +125
O
C unless otherwise noted.
+ _
10%
10 mA
2 mA
4 mA
6 mA
8 mA
Terminations
Blank = SM1
SM3 = Solder Dipped
SM5 = Solder Dipped
O
O
C
C
O
C (Military)
= Gold Plated
1
(Commercial)
(Industrial)
/
SM3
2
(Lead Free)
sine
Frequency
K = kHz
M = MHz
32.0M ,
Calibration
Tolerance
(in ppm)
@ 25
*
When enabled (PIN 1 is high*)
When disabled (PIN 1 is low)
When re-enabled (PIN 1 changes from low to high)
100
ABSOLUTE MAXIMUM RATINGS
Supply Voltage V
Storage Temperature
Maximum Process Temperature 260
ENABLE/DISABLE OPTIONS (E/T/N)
Statek offers three enable/disable options: E, T, and N.
Both the E-version and T-version have Tri-State outputs
and differ in whether the oscillator continues to run
internally when the output is put into the high Z state: it
stops in the E-version and continues to run in the
T-version. So, the E-version offers very low current
consumption when the oscillator is disabled and the
T-version offers very fast output recovery when the
oscillator is re-enabled. The N-version does not have
PIN 1 connected internally and so has no enable/disable
capability.
options.
When PIN 1 is allowed to float, it is held high by an internal pull-up resistor.
ENABLE/DISABLE OPTIONS E AND T
Output
Oscillator
Current consumption
Output
Oscillator
Current consumption
Output recovery
0
C
/
/
Stability over
Temp.Range
OR
Frequency
(in ppm)
100
The following table summarizes the three
COMPARISON OF
/
DD
/
Frequency
Tolerance
(in ppm)
200
Total
Freq. output
Oscillates
Normal
High Z state
Stops
Very low
Delayed
/
/
Temp. Range:
C = -10
I
M = -55
S = Customer Specified
Temp. Range:
C = -10
I
M = -55
S = Customer Specified
E
= -40
= -40
-0.5 V to 7.0 V
-55
I
I
O
O
O
O
O
O
O
O
C to +125
C to +70
C to +85
C to +125
C to +70
C to +85
C to +125
C for 20 seconds
Freq. output
Oscillates
Normal
High Z state
Oscillates
Lower than normal
Immediate
O
O
O
O
C
C
C
C
O
O
C
C
O
C
10172 Rev. A
T