MD54-0004TR MA-COM [M/A-COM Technology Solutions, Inc.], MD54-0004TR Datasheet - Page 2

• Manufacturer Part Number: MD54-0004TR
• Description: MMIC Medium Level Mixer 800 - 1000 MHz
• Manufacturer: MA-COM [M/A-COM Technology Solutions, Inc.]

2
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions
is considering for development. Performance is based on target specifications, simulated results,
and/or prototype measurements. Commitment to develop is not guaranteed.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available.
Commitment to produce in volume is not guaranteed.
MMIC Medium Level Mixer
800 - 1000 MHz
Absolute Maximum Ratings
MD54-0004
3. Exceeding any one or combination of these limits may cause
4. Total power for RF and LO ports should not exceed +23
Handling Procedures
Please observe the following precautions to avoid
damage:
Static Sensitivity
Gallium Arsenide Integrated Circuits are sensitive
to electrostatic discharge (ESD) and can be
damaged by static electricity. Proper ESD control
techniques should be used when handling these
devices.
Electrical Specifications:
Test Conditions: RF = 900 MHz (-10 dBm), LO = 840 MHz (13 dBm), IF = 60 MHz, T
2. IMR vs RF drive level can be calculated by the formula: IMR = 45 - (1.5 x P
permanent damage to this
dBm.
Input 1 dB Compression
Operating Temperature
Storage Temperature
Two-Tone IM Ratio
RF Input Power
LO Drive Power
Conversion Loss
Parameter
Parameter
Isolation
VSWR
4
4
2
device.
Absolute Maximum
-65°C to +150°C
-40°C to +85°C
3
Tone spacing 100 kHz, IF = 60 MHz
RF Freq. = 900 MHz, LO = +13 dBm
+22 dBm
+23 dBm
Two tones at –10 dBm each,
Test Conditions
LO to RF
LO to IF
RF to IF
LO Port
RF Port
IF Port
—
M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make
changes to the product(s) or information contained herein without notice.
Spurious Table
The spurious table shows the spurious signals resulting from the
mixing of the RF and LO input signals, assuming down
conversion. Mixing products are indicated by the number of dB
below the conversion loss. The lower frequency mixing term is
shown for two different RF input levels. The top number is for an
RF input power of -5 dBm, the lower number is for -15 dBm.
|mF
|mF
RF Frequency = 900 MHz
LO Frequency = 840 MHz
• North America Tel: [phone] • Europe Tel: [phone]
• India Tel: [phone]
IN
Visit www.macomtech.com for additional data sheets and product information.
RF
RF
)
- nF
- nF
4x
3x
2x
1x
0x
LO
LO
|, RF = -5 dBm
|, RF = -15 dBm
Units
Ratio
Ratio
Ratio
dBm
dBc
-12.2
dB
dB
dB
dB
-1.1
-7.7
-7.1
-2.2
8.9
2.2
2.9
0x
X
X
Harmonic of RF
40.1
39.9
34.2
34.1
23.7
23.8
4.7
4.8
1x
0
0
Min
25
45
—
—
—
—
—
—
—
• China Tel: [phone]
70.1
61.6
59.8
63.8
72.8
64.7
61.4
63.3
65.1
61.3
2x
A
2.5:1
2.0:1
2.0:1
Typ
+21
7.5
38
22
12
60
= +25°C
69.9
63.9
67.3
64.5
72.9
63.3
71.3
61.8
71.5
61.9
3x
Max
Rev. V5
9.5
—
—
—
—
—
—
—
—
73.4
64.4
71.9
61.9
71.1
61.9
72.1
62.3
4x
73
63