E5CS-Q1KJX OMRON [Omron Electronics LLC], E5CS-Q1KJX Datasheet
E5CS-Q1KJX
Related parts for E5CS-Q1KJX
E5CS-Q1KJX Summary of contents
Page 1
... ON/OFF or PID E5CS-RKJX E5CS-QKJX E5CS-R1KJX E5CS-Q1KJX E5CS-X J (IC) Iron-constantan 999 999 600 300 200 500 ...
Page 2
... Relay output Voltage output The functions can be factory-set for shipment as shown in the table below, depending on the suffix attached to the model number when you place your order. Two suffixes are selectable: “-DIN” or “-F”. Example: E5CS-RKJX-DIN Suffix Suffix Standard temperature ...
Page 3
... Accessories (Order Separately) Protective Cover Y92A-48 The protective cover protects the front panel, particularly the setting section, against dust, dirt, and water drip. It also prevents the set values from being altered due to accidental contact with the setting keys. Y92A-48 Protective Cover E5CS-X 3 ...
Page 4
... Operating: – Storage: – 35% to 85% RH IEC 144 Front panel: IP50 Rear panel: IP30 Terminals: IP00 Mechanical: 10,000,000 operations min. (relay output) Electrical: 100,000 operations min. (relay output) Approx. 170 g (main enclosure only Maximum of temperature range set E5CS-X ...
Page 5
... Lights when the alarm output relay is energized. Upward Setting Key When pressed, increases the set temperature/alarm value. Successively increases the value when held down. Downward Setting Key When pressed, decreases the set temperature/alarm value. Successively decreases the value when held down. E5CS-X 5 ...
Page 6
... The set tem- perature is displayed when power is turned ON. 2. The temperature range that can actually be indicated for a set temperature range of – – For other temperature range settings it is the full scale 10%. E5CS-X ...
Page 7
... OFF ON OFF ON OFF ON OFF Alarm output set with standby sequence will operate in the way shown below when the temperature drops below the upper-limit. E5CS-X Mode Alarm output OFF indicates the set temperature. 7 ...
Page 8
... C). In this case, the previously calculated and set proportional band is used. The Temperature Controller is provided with an overshoot preven- tion function that suppresses the second overshoot and those that follow to a level less than the initial overshoot. E5CS ...
Page 9
... Consequently, if the input shift func- tion is not needed, with pin 4 activated set the input shift value to 0. Display blinks Display blinks blinks blinks increases to about 140 Display E5CS-X Temperature Temperature measured by displayed sensor 100 C 100 C (without shift) 100 C ...
Page 10
... Platinum resistance thermometer type 10 Cause Voltage output type VDC Relay output type Thermocouple type Thermistor type E5CS-X Control output OFF during heating (reverse) ON during cooling (normal) ON during heating (reverse) OFF during cooling (normal) OFF OFF Both control output and alarm output are OFF ...
Page 11
... Note: All units are in millimeters unless otherwise indicated. Panel cutout Note: 1. The recommended panel thickness mm. 2. The Temperature Controller is contained in a mount- ing bracket, so close side-by-side Temperature Controller mounting is possible. Provide a center-to- center distance of at least 60 mm between two adja- cent Temperature Controllers. E5CS-X 11 ...
Page 12
... E5CS-X Precautions Mounting All Temperature Controllers in the E5CS-X Series conform to DIN43700 standard. The recommended panel thickness mm. Flush Mounting Insert the Temperature Controller, back end first, into the hole of the mounting panel. Mount the adapter by pushing it forward from the back of the Temperature Controller. Push the adapter as close as possible to the front panel of the Temperature Controller to eliminate the gap between them ...