NICFP-2200 NI [National Instruments Corporation], NICFP-2200 Datasheet - Page 3

• Manufacturer Part Number: NICFP-2200
• Description: Compact FieldPoint Real-Time Controllers
• Manufacturer: NI [National Instruments Corporation]

Compact FieldPoint Real-Time Controllers
Specifications
Specifications subject to change without notice. The following
specifications are typical for the range -40 to 70 °C unless
otherwise noted.
Memory
cFP-2200.............................................. 128 MB nonvolatile;
cFP-2210.............................................. 128 MB nonvolatile;
cFP-2220.............................................. 256 MB nonvolatile;
Memory lifetime (nonvolatile) ............ 100,000 writes per block
Network
Network interface............................... 10BASE-T and
Compatibility ....................................... IEEE 802.3
Communication rates.......................... 10 Mb/s, 100 Mb/s, autonegotiated
Maximum cabling distance................. 100 m/segment
Serial Ports
cFP-2200.............................................. 1 RS232 port
cFP-2210.............................................. 2 RS232 ports
cFP-2220.............................................. 3 RS232 ports; 1 RS485 port
RS232 (DTE) Ports
Baud rate............................................. Up to 115,200 b/s
Data bits.............................................. 5, 6, 7, 8
Stop bits.............................................. 1, 1.5, 2
Parity ................................................... Odd, Even, Mark, Space
Flow control ........................................ RTS/CTS, XON/XOFF, DTR/DSR
RS485 (DTE) Port
Baud rate............................................. 9,600 to 115,200 b/s
Data bits.............................................. 5, 6, 7, 8
Stop bits.............................................. 1, 1.5, 2
Parity ................................................... Odd, Even, Mark, Space
Flow control ........................................ XON/XOFF
Wire mode .......................................... 4-wire isolation voltage,
USB Port (cFP-2220 only)
Maximum data rate ........................... 12 Mb/s
Maximum current ............................... 500 mA
Continuous...................................... 100 V
Dielectric withstand ....................... 740 V
128 MB DRAM
256 MB DRAM
256 MB DRAM
100BASE-TX Ethernet
port to earth ground
rms
rms
, verified by 5 s test
Power Requirements
Caution: You must use a National Electric Code (NEC) UL-listed
Class 2 power supply with cFP-22xx controllers.
Power supply range ............................ 11 to 30 VDC
Recommended power supply
Power consumption ............................ 6.1 W + 1.1 (I/O module
Physical Characteristics
If you need to clean the controller, wipe it with a dry towel.
Screw-terminal wiring ........................ Use copper conductor wire with
Torque for screw terminals................. 0.5 to 0.6 N•m (4.4 to 5.3 lb•in.)
Weight................................................. 278 g (9.8 oz)
Environmental
The cFP-22xx controllers are intended for indoor use only, but they may
be used outdoors if mounted in a suitably sealed enclosure.
Operating temperature
(IEC 60068-2-1, IEC 60068-2-2)........... -40 to 70 °C
Storage temperature
(IEC 60068-2-1, IEC 60068-2-2)........... -55 to 85 °C
Operating humidity
(IEC 60068-2-56).................................. 10 to 90% RH, noncondensing
Storage humidity (IEC 60068-2-56)..... 5 to 95% RH, noncondensing
Maximum altitude............................... 2,000 m
Pollution degree (IEC 60664) .............. 2
Shock and Vibration
To meet these specifications, you must panel mount the Compact FieldPoint
system and affix ferrules to the ends of the power terminal wires.
Operating shock (IEC 60068-2-27) ...... 30 g, 11 ms half sine; 50 g,
Operating vibration, random
(IEC 60068-2-64).................................. 5 g
Operating vibration, sinusoidal
(IEC 60068-2-6).................................... 5 g, 10 to 500 Hz
Safety Voltages
Connect only voltages that are within these limits
V terminal to C terminal ..................... 35 V max, Measurement Category I
Caution: Do not connect the system to signals or use for measurements
within Measurement Category II, III, or IV.
cFP-BP-4 system ............................. 15 W
cFP-BP-8 system ............................. 20 W
External digital I/O terminals ......... 16 to 28 AWG
Power supply terminals .................. 14 to 30 AWG
BUY ONLINE at ni.com or CALL 800 813 3693 (U.S.)
power requirements)
10 mm (0.39 in.) of insulation
stripped from the end
3 ms half sine; 18 shocks at
6 orientations
rms
, 10 to 500 Hz
3