SLIN-02E2A BEL [Bel Fuse Inc.], SLIN-02E2A Datasheet - Page 3

• Manufacturer Part Number: SLIN-02E2A
• Description: NON-ISOLATED DC/DC CONVERTERS
• Manufacturer: BEL [Bel Fuse Inc.]

Output Specifications
Notes: 1. Some output voltages may not be possible depending on the input voltage.
January 14, 2011
Output Voltage Set Point
Output Voltage
Adjustment Range
Remote Sense Range
Load Regulation
Line Regulation
Temperature Regulation
(-40°C to +85°C)
Ripple and Noise (pk-pk)
Ripple and Noise (rms)
Output Current Range
Output DC Current Limit
Output Short-Circuit Current
Output Capacitance
Turn-On Delay Time
Output voltage Rise time
Output voltage overshoot
NON-ISOLATED DC/DC CONVERTERS
3 Vdc - 14 Vdc Input, 0.6 Vdc - 5.5 Vdc /2 A Outputs
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel [phone] • Fax [phone] •
3. Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and
2. External capacitors may require using the new Tunable Loop
stable as well as getting the best transient response (See the Tunable Loop
temperature conditions.
Parameter
ESR≥0.15 mΩ
ESR≥ 10 mΩ
ESR≥ 1 mΩ
1
V
V
V
V
2
O
O
O
O
≥ 2.5V
≥ 2.5V
< 2.5V
< 2.5V
Min
-1.5
-2.5
0.6
22
0
0
0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Typ
180
140
5.2
1.4
50
20
5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
1000
3000
Max
+1.5
+2.5
100
5.5
0.5
0.4
0.4
3.0
10
10
38
47
5
2
-
-
-
%Io,max
%Vo,set
%Vo,set
%Vo,set
%Vo,set
%Vo,set
Unit
mV
mV
mV
mV
mV
mA
mS
mS
mS
uF
uF
uF
V
V
A
TM
feature to ensure that the module is
with 0.5% tolerance for external resistor
used to set output voltage
Over all operating input voltage, resistive
load, and temperature conditions until end
of life
selected by an external resistor
I
V
5Hz to 20MHz BW, V
min
capacitors)
in either sink or source mode
Hiccup Mode
Vo≤250mV, Hiccup Mode
Without the Tunable Loop
With the Tunable Loop
With the Tunable Loop
Case 1: On/Off input is enabled and then
input power is applied (delay from instant
at which V
Vo, set)
Case 2: Input power is applied for at least
one second and then the On/Off input is
enabled (delay from instant at which
Von/Off is enabled until Vo =10% of Vo,
set)
time for Vo to rise from 10% of Vo, set to
90% of Vo, set
Vin=Vin, min to Vin, max, Io=Io, min to Io,
max, With or without maximum external
capacitance
O
IN
=I
=V
to I
O, min
IN, min
O, max
to I
IN
to V
Co = 0.1μF // 10 μF ceramic
O, max
TM
= V
IN, max
section for details).
www.belfuse.com
IN, min
Notes
IN
until Vo =10% of
TM
TM
=V
IN, nom
TM
and I
O
=I
O,
3