AM42-0040_1 MACOM [Tyco Electronics], AM42-0040_1 Datasheet - Page 2

• Manufacturer Part Number: AM42-0040_1
• Description: GaAs MMIC VSAT Power Amplifier 2.0W 5.9 - 6.4GHz
• Manufacturer: MACOM [Tyco Electronics]

2
M/A-COM Inc. and its affiliates reserve the right to make changes to the
product(s) or information contained herein without notice. M/A-COM makes
no warranty, representation or guarantee regarding the suitability of its
products for any particular purpose, nor does M/A-COM assume any liability
whatsoever arising out of the use or application of any product(s) or
information.
GaAs MMIC VSAT Power Amplifier, 2.0 W
5.9 - 6.4 GHz
Absolute Maximum Ratings
1.
2.
3.
Electrical Specifications: T
Output Power vs. Temperature
Output Power vs. Frequency
(with respect to T
Exceeding any one or combination of these limits may cause
permanent damage to this device.
M/A-COM does not recommend sustained operation near
these survivability limits.
Case Temperature (T
Channel Temperature
Storage Temperature
Thermal Resistance
Drain Bias Current
Gate Bias Voltage
Gate Bias Current
Second Harmonic
Parameter
Third Harmonic
Input Power
Output VSWR
Output Power
Parameter
Input VSWR
Linear Gain
V
DD
V
V
I
V
DD
- V
GG
DD
DET
GG
A
= 25°C)
C
) = +25°C.
Absolute Maximum
-65°C to +150°C
-40°C to +85°C
P
P
P
P
P
P
P
A
+12 Volts
+12 Volts
+23 dBm
1700 mA
IN
IN
IN
IN
IN
IN
IN
1,2,3
-3 Volts
= 25°C, V
= +10 dBm, I
= +10 dBm, I
= +10 dBm, I
= +10 dBm, I
= +10 dBm, I
= +10 dBm, I
= +10 dBm, I
Test Conditions
T
A
25°C Heat Sink
= -40°C to +70°C
P
P
P
P
IN
IN
IN
IN
= +10 dBm
< -10 dBm
< -10 dBm
< -10 dBm
DD
DD
DD
DD
DD
DD
DD
DD
= 1050 mA Typ.
= 1050 mA Typ.
= 1050 mA Typ.
= 1050 mA Typ.
= 1050 mA Typ.
= 1050 mA Typ.
= 1050 mA Typ.
= +9 V, V
Compliant
• North America Tel: [phone] / Fax: [phone]
• Europe Tel: [phone] / Fax: [phone]
• Asia/Pacific Tel: [phone] / Fax: [phone]
Visit www.macom.com for additional data sheets and product information.
Typical Bias Configuration
4.
5.
6.
7.
8.
GG
Nominal bias is obtained by first connecting -2.4 volts to
pin 5 (V
Note sequence. Adjust V
typical.
RF ground and thermal interface is the flange (case bot-
tom). Adequate heat sinking is required.
No DC bias voltage appears at the RF ports.
For optimum IP3 performance, the V
should be placed within 0.5 inches of the V
Resistor and capacitors surrounding the amplifier are
suggestions and not included as part of the AM42-0040.
RoHS
adjusted for I
GG
Units
Ratio
Ratio
°C/W
), followed by connection +9 volts to pin 10 (V
dBm
dBc
dBc
mA
mA
dB
dB
dB
V
V
DD
Min.
31.7
-2.4
900
27
—
—
—
—
—
—
—
—
GG
2
= 1050 mA
for a drain current of 1050 mA
DD
4,5,6,7,8
Typ.
2.3:1
3.0:1
1050
33.0
±0.4
-1.2
1.0
5.6
-35
-45
30
—
bypass capacitors
5
DD
AM42-0040
leads.
Max.
2.7:1
1100
34.5
-0.4
1.5
—
—
—
20
—
—
—
—
DD
V3
).