PI5C3390QE Pericom Semiconductor, PI5C3390QE Datasheet - Page 3

• Manufacturer Part Number: PI5C3390QE
• Description: IC 16:8 MUX/DEMUX BUS SW 28-QSOP
• Manufacturer: Pericom Semiconductor
• Type: Multiplexer/Demultiplexerr

Specifications of PI5C3390QE

• Circuit: 8 x 1:1
• Independent Circuits: 2
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 28-QSOP
• Configuration: 8 x 2:1
• Number Of Inputs: 16
• Number Of Outputs: 8
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (min): 4.75V
• Operating Supply Voltage (max): 5.25V
• Power Dissipation: 500mW
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 28
• Package Type: QSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Supply: -
• Current - Output High, Low: -
• Lead Free Status / Rohs Status: Compliant

Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device.
2. Typical values are at Vcc = 5.0V, +25°C ambient.
3. Per TTL driven input (V
4. This current applies to the control inputs only and represent the current required to switch internal capacitance at the specified frequency. The
PI5C3390 Switching Characteristics over Operating Range
Notes:
1. See test circuit and waveforms.
2. This parameter is guaranteed but not tested on Propagation Delays.
3. The bus switch contributes no propagational delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The
Power Supply Characteristics
Parameters Description
Parameters
A, B, and C inputs generate no significant AC or DC currents as they transition. This parameter is not tested, but is guaranteed by design.
time constant for the switch alone is of the order of 0.25ns for 50pF load. Since this time constant is much smaller than the rise/fall times of
typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is
determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side.
I
ΔI
I
t
t
t
t
t
t
CC
CCD
PLH
PHL
PZH
PZL
PHZ
PLZ
CC
07-0126
Quiescent Power
Supply Current
Supply Current per
Input @ TTL HIGH
Supply Current per
Input per MHz
Description
Propagation Delay
A, B to/from C
Bus Enable Time
AEN/BEN to A, B, C
Bus Disable Time
AEN/BEN to A, B, C
IN
= 3.4V, control inputs only); A, B, and C pins do not contribute to Icc.
(4)
(2,3)
R
Conditions
C
L
= 500-ohm
L
= 50 pF
V
V
V
A, B, and C Pins Open
BE = GND
Control Input Toggling
50% Duty Cycle
CC
CC
CC
= Max.
= Max.
= Max.,
(1)
Test Conditions
Min.
1.5
1.5
3
PI5C3390
Com
Typ.
0.25
(1)
V
V
IN
IN
16:8 Multiplexer/Demultiplexer Bus Switch
= 3.4V
= GND or V
Max.
6.5
5.5
(3)
CC
Unit
ns
ns
ns
Min.
PI5C3390; PI5C32390
Typ
0.2
(2)
PS7030J
Max.
0.25
3.5
30
Units
MHz
mA/
mA
μA
05/02/07