PI3CH401LE Pericom Semiconductor, PI3CH401LE Datasheet - Page 2

• Manufacturer Part Number: PI3CH401LE
• Description: IC 4-CH SWITCH 2-PORT 16-TSSOP
• Manufacturer: Pericom Semiconductor
• Type: Bus Switchr

Specifications of PI3CH401LE

• Circuit: 1 x 1:1
• Independent Circuits: 4
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-TSSOP
• Number Of Bits: 4
• Number Of Elements: 4
• High Level Output Current: -120mA
• Low Level Output Current: 120mA
• Package Type: TSSOP
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.63V
• Pin Count: 16
• Mounting: Surface Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Supply: -
• Current - Output High, Low: -
• Lead Free Status / Rohs Status: Compliant

Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
DC Electrical Characteristics, 3.3V Supply
Notes:
1.
2.
3.
DC Electrical Characteristics, 2.5V Supply
Notes:
1.
2.
3.
Parameters
Parameters
Storage Temperature ................................................ –65°C to +150°C
Ambient Temperature with Power Applied ............... –40°C to +85°C
Supply Voltage to Ground Potential ........................... –0.5V to +4.6V
DC Input Voltage ........................................................ –0.5V to +6.0V
DC Output Current................................................................... 120mA
Power Dissipation ....................................................................... 0.5W
For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
Typical values are at V
Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined
by the lower of the voltages on the two (A,B) pins.
For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
Typical values are at V
Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined
by the lower of the voltages on the two (A,B) pins.
I
I
R
R
V
V
V
V
V
OZH
V
I
OZH
I
I
I
IH
IL
ON
IH
IL
ON
IH
IK
IL
IH
IK
IL
06-0235
Input HIGH Voltage
Input LOW Voltage
Clamp Diode Voltage
Input HIGH Current
Input LOW Current
High-Impedence Current
Switch On-Resistance
Input HIGH Voltage
Inout LOW Voltage
Clamp Diode Voltage
Input HIGH Current
Input LOW Current
High Impedance Current
Switch On-Resistance
Description
Description
CC
CC
= 3.3V, T
= 3.3V, T
A
A
= 25°C ambient and maximum loading.
= 25°C ambient and maximum loading.
(3)
(3)
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
V
V
V
0 ≤ A, B ≤ V
V
I
V
I
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
V
V
V
0 ≤ A, B ≤ V
V
I
V
ADVANCE INFORMATION
ON
ON
ON
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
= 48mA
= –15mA
= 48mA or 64mA
= Max., I
= Max., V
= Max., V
= Min., V
= Min., V
= Min., I
= Max., V
= Max., V
= Min.,V
= Min., V
(Over Operating Range, T
(Over Operating Range, T
Test Conditions
CC
CC
Test Conditions
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
= –18mA
= –6mA
= 0V,
= 0V,
= 2.25V,
= GND
= 3.6V, I
= V
2
= V
= GND
CC
CC
ON
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at these
or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect re-
liability.
(1)
= –15mA
(1)
A
A
= –40°C to +85°C, V
= –40°C to +85°C, V
Min.
–0.3
1.8
Low Voltage, 5Ω, 4-Channel
Min.
–0.5
2
Typ.
–0.7
CC
CC
4
7
Typ.
(2)
2-Port NanoSwitch
= 3.3V ± 10%)
= 2.5V ± 10%)
–0.8
4
5
(2)
V
CC
Max.
–1.8
0.8
±1
±1
±1
14
8
Max.
+ 0.3
P-0.6
–1.8
0.8
±1
±1
±1
6
8
PI3CH401
Units
Units
µA
µA
Ω
Ω
05/10/06
V
V
™