HFBR-1402C HP [Agilent(Hewlett-Packard)], HFBR-1402C Datasheet - Page 21

• Manufacturer Part Number: HFBR-1402C
• Description: Components is Designed to Provide cost effective, High performance fiber optic communication links
• Manufacturer: HP [Agilent(Hewlett-Packard)]

Electrical/Optical Characteristics -40 °C to + 85 °C unless otherwise specified
Fiber sizes with core diameter ≤ 100 µm and NA ≤ 0.35, 4.75 V ≤ V
Dynamic Characteristics
-40 °C to +85 °C unless otherwise specified; 4.75 V ≤ V
Notes:
1. 2.0 mm from where leads enter case.
2. 8 mA load (5 x 1.6 mA), RL = 560 W.
3. Typical data at T
4. D is the effective diameter of the detector image on the plane of the fiber face. The numerical value is the product of the actual detector diameter
5. Measured at the end of 100/140 mm fiber optic cable with large area detector.
6. Propagation delay through the system is the result of several sequentially-occurring phenomena. Consequently it is a combination of data-rate-
7. As the cable length is increased, the propagation delays increase at 5 ns per meter of length. Data rate, as limited by pulse width distortion, is not
21
Parameter
High Level Output Current
Low Level Output Voltage
High Level Supply Current
Low Level Supply Current
Equivalent NA
Optical Port Diameter
Parameter
Peak Optical Input Power Logic Level HIGH
Peak Optical Input Power Logic Level LOW
Propagation Delay LOW to HIGH
Propagation Delay HIGH to LOW
CAUTION: The small junction sizes inherent to the design of these components increase the components’ susceptibility to damage
from electrostatic discharge (ESD). It is advised that normal static precautions be taken in handling and assembly of these
components to prevent damage and/or degradation which may be induced by ESD.
and the lens magnification.
limiting effects and of transmission-time effects. Because of this, the data-rate limit of the system must be described in terms of time differentials
between delays imposed on falling and rising edges.
affected by increasing cable length if the optical power level at the receiver is maintained.
A
= +25 °C, V
CC
= 5.0 Vdc.
Symbol
I
I
I
NA
D
Symbol
P
P
V
t
t
OH
CCH
CCL
PLHR
PHLR
RH
RL
OL
Min
Min
-25.4
2.9
-24.0
4.0
CC
≤ 5.25 V; BER ≤ 10-9
5
0.4
3.5
6.2
0.50
400
65
Typ
Typ
49
3
3
CC
≤ 5.25 V
Max
0.5
6.3
10
Max
120
100
250
-40
0.1
-9.2
-10.0
Units
µA
mA
mA
µm
Units
ns
ns
V
dBm pk
µW pk
dBm pk
µW pk
dBm pk
µW pk
Conditions
P
I
P
P
P
V
V
V
Conditions
I
I
P
Data Rate =
5 MBd
l
T
T
O
OL
OL
R
R
R
R
A
A
R
O
CC
CC
P
= 8 mA
< -40 dBm
> -24 dBm
< -40 dBm
> -24 dBm
= 8mA
= 8mA
= -21 dBm,
= 18
= +25 °C,
= +25 °C,
= 820 nm
= 5.25 V
= 5.25 V
Reference
Note 4
Reference
Note 5
Note 5
Note 6