HI-1575 HOLTIC [Holt Integrated Circuits], HI-1575 Datasheet - Page 8

• Manufacturer Part Number: HI-1575
• Description: 3.3V Dual Transceivers with Integrated Encoder / Decoders
• Manufacturer: HOLTIC [Holt Integrated Circuits]

DC ELECTRICAL CHARACTERISTICS
VDD = 3.3 V, GND = 0V, T = Operating Temperature Range (unless otherwise specified).
ABSOLUTE MAXIMUM RATINGS
Operating Voltage
Total Supply Current
TRANSMITTER(Measured at Point “A ” in Figure 12 unless otherwise specified)
Output Voltage
Power Dissipation
Min. Input Voltage
Max. Input Voltage
Output Noise
Supply voltage (
Logic input voltage range
Receiver differential voltage
Driver peak output current
Power dissipation at 25°C
Solder Temperature
Junction Temperature
Storage Temperature
Min. Input Current
Max. Input Current
Pull-up / Pull-down current
Min. Output Voltage
Max. Output Voltage (LO)
RECEIVER
Input resistance
Output Dynamic Offset Voltage
Input capacitance
Common mode rejection ratio
Input Level
Input common mode voltage
Threshold Voltage - Direct-coupled
Theshold Voltage -
Output resistance
Transformer-coupled
VDD)
(Measured at Point “A “ in Figure 12 unless otherwise specified)
PARAMETER
(LO)
(LO)
(HI)
(HI)
(HI)
A
Transformer coupled
Transformer coupled
Direct coupled
Direct coupled
D
No Detect
No Detect
Detect
Detect
D
-0.3 V DC to +3.6 V
275°C for 10 sec.
-65°C to +150°C
-0.3 V to +5 V
+/- 10 Vp-p
HOLT INTEGRATED CIRCUITS
SYMBOL
+1.0 A
175°C
1.0 W
V
V
V
V
C
V
V
R
V
I
I
I
V
V
P
P
I
V
V
V
CC1
CC2
CC3
V
V
PUD
V
R
C
V
THND
THND
OUT
OUT
I
I
DYN
MRR
DYN
DD
THD
THD
OUT
D1
IH
ICM
ON
D2
IL
OH
IH
IL
IH
IN
IN
IN
(Measured at Point “A “ in Figure 12)
(Measured at Point “A “ in Figure 12)
(Measured at Point “A “ in Figure 13)
(Measured at Point “A “ in Figure 13)
(Measured at Point “A “ in Figure 12)
(Measured at Point “A “ in Figure 13)
HI-1575
Digital inputs (without pull-down)
Differential, not transmitting
Digital inputs (without pull-up)
I
I
OUT
OUT
Digital inputs and data bus
8
Transmit one channel @
Transmit one channel @
Transmit one channel @
Differential, inhibited
RECOMMENDED OPERATING CONDITIONS
1 MHz Sine Wave
1 Mhz Sine Wave
= -1.0mA, Digital outputs
= 1.0mA, Digital outputs
NOTE:
ratings or outside recommended operating
conditions may cause permanent damage to the
device. These are stress ratings only. Operation
at the limits is not recommended.
Not Transmitting
100% duty cycle
Not Transmitting
100% duty cycle
35 ohm load
70
50% duty cycle
35 ohm load
70 ohm load
CONDITION
Supply Voltage
Temperature Range
Digital inputs
Digital inputs
Differential
Differential
Differential
ohm load
VDD....................................... 3.3V... ±5%
Industrial Screening.........-40°C to +85°C
Hi-Temp Screening........-55°C to +125°C
D
D
T
T
D
T
Stresses above absolute maximum
MIN
3.15
70%
18.0
90%
-250
1.15
0.86
6.0
-20
-5.0
-90
20
40
10
TYP
3.30
225
425
275
0.3
4
MAX
3.45
0.06
30%
27.0
250
10%
10.0
50
0.28
0.20
9.0
250
0.5
10
20
5.0
90
5
9
0
UNITS
mVp-p
Kohm
Kohm
Vp-p
Vp-p
V
V
V
V
Vp-p
Vp-p
Vp-p
Vp-p
Vp-p
mA
mA
mA
V-pk
mV
mV
µA
µA
uA
W
W
pF
dB
V
DD
DD
DD
DD