AM29SL800DB120WAC AMD [Advanced Micro Devices], AM29SL800DB120WAC Datasheet - Page 21

• Manufacturer Part Number: AM29SL800DB120WAC
• Description: 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 1.8 Volt-only Super Low Voltage Flash Memory
• Manufacturer: AMD [Advanced Micro Devices]

Legend:
X = Don’t care
RA = Address of the memory location to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed. Addresses
latch on the falling edge of the WE# or CE# pulse, whichever
happens later.
Notes:
1. See Table 1 for description of bus operations.
2. All values are in hexadecimal.
3. Except when reading array or autoselect data, all bus cycles are
4. Data bits DQ15–DQ8 are don’t cares for unlock and command
5. Address bits A18–A11 are don’t cares for unlock and command
6. No unlock or command cycles required when reading array data,
7. The Reset command is required to return to reading array data
8. The fourth cycle of the autoselect command sequence is a read
January 23, 2007 27546A6
Read (Note 6)
Reset (Note 7)
Program
Unlock Bypass
Unlock Bypass Program (Note 10)
Unlock Bypass Reset (Note 11)
Chip Erase
Sector Erase
Erase Suspend (Note 12)
Erase Resume (Note 13)
write operations.
cycles.
cycles, unless SA or PA required.
unless SA or PA required.
when device is in the autoselect mode, or if DQ5 goes high (while
the device is providing status data).
cycle.
Manufacturer ID
Device ID,
Top Boot Block
Device ID,
Bottom Boot Block
Sector Protect Verify
(Note 9)
Extension
Command
Sequence
(Note 1)
Word
Word
Word
Word
Word
Word
Word
Word
Word
Byte
Byte
Byte
Byte
Byte
Byte
Byte
Byte
Byte
Table 5. Am29SL800D Command Definitions
1
1
4
4
4
4
4
4
3
2
2
6
6
1
1
Addr
XXX
AAA
AAA
AAA
AAA
AAA
AAA
AAA
XXX
XXX
AAA
AAA
XXX
XXX
555
555
555
555
555
555
555
555
555
RA
First
Data
RD
AA
AA
AA
AA
AA
AA
AA
AA
AA
D A T A
F0
A0
B0
90
30
Addr
XXX
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
555
555
555
555
555
555
555
555
555
PA
Am29SL800D
Second
Data
PD
S H E E T
55
55
55
55
55
55
55
00
55
55
PD = Data to be programmed at location PA. Data latches on the
rising edge of WE# or CE# pulse, whichever happens first.
SA = Address of the sector to be verified (in autoselect mode) or
erased. Address bits A18–A12 uniquely select any sector.
9. The data is 00h for an unprotected sector and 01h for a protected
10. The Unlock Bypass command is required prior to the Unlock
11. The Unlock Bypass Reset command is required to return to
12. The system may read and program in non-erasing sectors, or enter the
13. The Erase Resume command is valid only during the Erase Suspend
sector.
information.
Bypass Program command.
reading array data when the device is in the unlock bypass mode.
autoselect mode, when in the Erase Suspend mode. The Erase Suspend
command is valid only during a sector erase operation.
mode.
Addr
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
555
555
555
555
555
555
555
555
555
Bus Cycles (Notes 2-5)
Third
See “Autoselect Command Sequence”
Data
90
90
90
90
90
A0
20
80
80
Addr
(SA)
(SA)
AAA
AAA
X00
X01
X02
X01
X02
X02
X04
X03
X04
555
555
PA
Fourth
22EA
226B
XX00
XX01
Data
TBD
TBD
TBD
TBD
PD
EA
AA
AA
01
6B
00
01
Addr
2AA
2AA
555
555
Fifth
Data
55
55
for more
Addr
AAA
555
SA
Sixth
Data
10
30
19