MC74HCT373ANG ON Semiconductor, MC74HCT373ANG Datasheet - Page 8
![IC LATCH TRNSP OCTAL 3ST 20DIP](/photos/7/4/70408/20-dip_738_sml.jpg)
MC74HCT373ANG
Manufacturer Part Number
MC74HCT373ANG
Description
IC LATCH TRNSP OCTAL 3ST 20DIP
Manufacturer
ON Semiconductor
Series
74HCTr
Datasheet
1.MC74HCT373ADTR2G.pdf
(8 pages)
Specifications of MC74HCT373ANG
Logic Type
D-Type Transparent Latch
Circuit
8:8
Output Type
Tri-State
Voltage - Supply
4.5 V ~ 5.5 V
Independent Circuits
1
Delay Time - Propagation
28ns
Current - Output High, Low
6mA, 6mA
Operating Temperature
-55°C ~ 125°C
Mounting Type
Through Hole
Package / Case
20-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
MC74HCT373ANGOS
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor and
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
0.15 (0.006) T
0.15 (0.006) T
L
2X
−T−
U
PIN 1
IDENT
U
L/2
C
0.100 (0.004)
S
S
SEATING
PLANE
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
20
1
D
20X
−V−
0.10 (0.004)
A
K
REF
G
H
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Japan: ON Semiconductor, Japan Customer Focus Center
M
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
PACKAGE DIMENSIONS
10
11
T
U
http://onsemi.com
−U−
CASE 948E−02
S
B
DT SUFFIX
TSSOP−20
ISSUE A
V
S
8
J J1
N
N
Í Í Í Í
Í Í Í Í
Í Í Í Í
DETAIL E
SECTION N−N
DETAIL E
F
K1
0.25 (0.010)
K
M
−W−
NOTES:
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
For additional information, please contact your
local Sales Representative.
1.
2.
3.
4.
5.
6.
7.
Y14.5M, 1982.
FLASH, PROTRUSIONS OR GATE BURRS. MOLD
FLASH OR GATE BURRS SHALL NOT EXCEED
0.15 (0.006) PER SIDE.
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL NOT
EXCEED 0.25 (0.010) PER SIDE.
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN
EXCESS OF THE K DIMENSION AT MAXIMUM
MATERIAL CONDITION.
REFERENCE ONLY.
DETERMINED AT DATUM PLANE −W−.
DIM
K1
J1
G
M
A
B
C
D
F
H
J
K
L
DIMENSIONING AND TOLERANCING PER ANSI
CONTROLLING DIMENSION: MILLIMETER.
DIMENSION A DOES NOT INCLUDE MOLD
DIMENSION B DOES NOT INCLUDE
DIMENSION K DOES NOT INCLUDE DAMBAR
TERMINAL NUMBERS ARE SHOWN FOR
DIMENSION A AND B ARE TO BE
MILLIMETERS
MIN
6.40
4.30
0.05
0.50
0.27
0.09
0.09
0.19
0.19
−−−
0
0.65 BSC
6.40 BSC
_
MAX
6.60
4.50
1.20
0.15
0.75
0.37
0.20
0.16
0.30
0.25
8
_
MC74HCT373A/D
0.252
0.169
0.002
0.020
0.011
0.004
0.004
0.007
0.007
MIN
−−−
0.026 BSC
0.252 BSC
0
_
INCHES
0.260
0.177
0.047
0.006
0.030
0.015
0.008
0.006
0.012
0.010
MAX
8
_