AM29DL640D120 AMD [Advanced Micro Devices], AM29DL640D120 Datasheet - Page 9

• Manufacturer Part Number: AM29DL640D120
• Description: 64 Megabit CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory
• Manufacturer: AMD [Advanced Micro Devices]

DEVICE BUS OPERATIONS
This section describes the requirements and use of
the device bus operations, which are initiated through
the internal command register. The command register
itself does not occupy any addressable memory loca-
ti on . T he re gi s ter is a la tc h u s ed to s tore th e
commands, along with the address and data informa-
tion needed to execute the command. The contents of
Legend: L = Logic Low = V
A
Notes:
1. Addresses are A21:A0 in word mode (BYTE# = V
2. The sector protect and sector unprotect functions may also be implemented via programming equipment. See the “Sector/Sector
3. If WP#/ACC = V
Word/Byte Configuration
The BYTE# pin controls whether the device data I/O
pins operate in the byte or word configuration. If the
BYTE# pin is set at logic ‘1’, the device is in word con-
figuration, DQ0–DQ15 are active and controlled by
CE# and OE#.
If the BYTE# pin is set at logic ‘0’, the device is in byte
configuration, and only data I/O pins DQ0–DQ7 are
active and controlled by CE# and OE#. The data I/O
pins DQ8–DQ14 are tri-stated, and the DQ15 pin is
used as an input for the LSB (A-1) address function.
8
Read
Write
Standby
Output Disable
Reset
Sector Protect (Note 2)
Sector Unprotect (Note 2)
Temporary Sector
Unprotect
IN
Block Protection and Unprotection” section.
depends on whether they were last protected or unprotected using the method described in “Sector/Sector Block Protection
and Unprotection”. If WP#/ACC = V
= Address In, D
Operation
IN
IL
, sectors 0, 1, 140, and 141 remain protected. If WP#/ACC = V
= Data In, D
V
IL
0.3 V
CE#
, H = Logic High = V
CC
L
L
L
X
L
L
X
±
OUT
Table 1. Am29DL640D Device Bus Operations
OE#
H
H
H
H
X
L
X
X
= Data Out
HH
, all sectors will be unprotected.
WE# RESET#
H
X
H
X
X
L
L
L
IH
V
0.3 V
, V
V
V
V
CC
H
H
H
L
ID
ID
ID
IH
ID
±
), A21:A-1 in byte mode (BYTE# = V
Am29DL640D
= 8.5–12.5 V, V
WP#/ACC
(Note 3)
(Note 3)
(Note 3)
L/H
L/H
L/H
L/H
H
the register serve as inputs to the internal state ma-
chine. The state machine outputs dictate the function
of the device. Table 1 lists the device bus operations,
the inputs and control levels they require, and the re-
sulting output. The following subsections describe
each of these operations in further detail.
Requirements for Reading Array Data
To read array data from the outputs, the system must
drive the CE# and OE# pins to V
control and selects the device. OE# is the output con-
trol and gates array data to the output pins. WE#
should remain at V
whether the device outputs array data in words or
bytes.
The internal state machine is set for reading array data
upon device power-up, or after a hardware reset. This
ensures that no spurious alteration of the memory
content occurs during the power transition. No com-
mand is necessary in this mode to obtain array data.
Standard microprocessor read cycles that assert valid
HH
A1 = H, A0 = L
A1 = H, A0 = L
= 9.0 ± 0.5 V, X = Don’t Care, SA = Sector Address,
SA, A6 = H,
Addresses
SA, A6 = L,
(Note 2)
A
A
A
X
X
X
IN
IN
IN
IH
, protection on sectors 0, 1, 140, and 141
High-Z
High-Z
High-Z
DQ0–
IH
D
DQ7
D
D
D
D
IL
OUT
. The BYTE# pin determines
IN
IN
IN
IN
).
BYTE#
High-Z
High-Z
High-Z
= V
D
D
D
OUT
X
X
IN
IN
IH
IL
. CE# is the power
DQ8–DQ15
High-Z, DQ15 = A-1
October 7, 2004
DQ8–DQ14 =
BYTE#
High-Z
High-Z
High-Z
High-Z
= V
X
X
IL