LTM4607 LINER [Linear Technology], LTM4607 Datasheet - Page 12

• Manufacturer Part Number: LTM4607
• Description: 36VIN, 24VOUT High Effi ciency Buck-Boost DC/DC ?Module
• Manufacturer: LINER [Linear Technology]

APPLICATIONS INFORMATION
LTM4607
In buck mode, the allowed maximum average load cur-
rent is:
The maximum current sensing R
mode is:
The maximum current sensing R
mode is:
A 20% to 30% margin on the calculated sensing resistor is
usually recommended. Please refer to Table 3 for the rec-
ommended sensing resistors for different applications.
Soft-Start
The SS pin provides a means to soft-start the regulator.
A capacitor on this pin will program the ramp rate of the
output voltage. A 1.7μA current source will charge up the
external soft-start capacitor. This will control the ramp of
the internal reference and the output voltage. The total
soft-start time can be calculated as:
When the RUN pin falls below 1.6V, then soft-start pin is
reset to allow for proper soft-start control when the regula-
tor is enabled again. Current foldback and force continuous
mode are disabled during the soft-start process. The soft-
start function can also be used to control the output ramp
up time, so that another regulator can be easily tracked.
Do not apply more than 6V to the SS pin.
Run Enable
The RUN pin is used to enable the power module. The pin
can be driven with a logic input, and not exceed 6V.
12
I
R
R
t
2 •I
OUT(MAX,BUCK)
SOFTSTART
SENSE(MAX,BOOST)
SENSE(MAX,BUCK)
OUT(MAX,BOOST)
2 • 160mV • V
=
2.4V • C
=
1.7µA
R
130mV
=
SENSE
=
• V
2 •I
SS
OUT
OUT(MAX,BUCK)
IN
+
+ ΔI
2 • 130mV
ΔI
2
SENSE
SENSE
L
L
• V
value for the boost
IN
value for the buck
– ΔI
L
The RUN pin can also be used as an undervoltage lockout
(UVLO) function by connecting a resistor from the input
supply to the RUN pin. The equation:
Power Good
The PGOOD pin is an open drain pin that can be used to
monitor valid output voltage regulation. This pin monitors
a ±7.5% window around the regulation point, and tracks
with margining.
COMP Pin
This pin is the external compensation pin. The module
has already been internally compensated for most output
voltages. A spice model will be provided for other control
loop optimization.
Fault Conditions: Current Limit and Overcurrent
Foldback
LTM4607 has a current mode controller, which inherently
limits the cycle-by-cycle inductor current not only in steady
state operation, but also in transient. Refer to Table 3.
To further limit current in the event of an overload condi-
tion, the LTM4607 provides foldback current limiting. If the
output voltage falls by more than 70%, then the maximum
output current is progressively lowered to about 30% of
its full current limit value for boost mode and about 40%
for buck mode.
Standby Mode (STBYMD)
The standby mode (STBYMD) pin provides several choices
for start-up and standby operational modes. If the pin is
pulled to ground, the SS pin is internally pulled to ground,
preventing start-up and thereby providing a single control
pin for turning off the controller. If the pin is left open or
decoupled with a capacitor to ground, the SS pin is internally
provided with a starting current, permitting external control
for turning on the controller. If the pin is connected to a
voltage greater than 1.25V, the internal regulator (INTV
will be on even when the controller is shut down (RUN
V _UVLO =
R1+ R2
R2
• 1.6V
4607f
CC
)