AM29BDS320G SPANSION [SPANSION], AM29BDS320G Datasheet - Page 44
![no-image](/images/no-image-200.jpg)
AM29BDS320G
Manufacturer Part Number
AM29BDS320G
Description
32 Megabit (2 M x 16-Bit), 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory
Manufacturer
SPANSION [SPANSION]
Datasheet
1.AM29BDS320G.pdf
(74 pages)
Notes:
1. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits.
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for
3. When reading write operation status bits, the system must always provide the bank address where the Embedded
4. The system may read either asynchronously or synchronously (burst) while in erase suspend. RDY will function
42
Standard
Suspend
Refer to the section on DQ5 for more information.
further details.
Algorithm is in progress. The device outputs array data if the system addresses a non-busy bank.
exactly as in non-erase-suspended mode.
Erase
Mode
Mode
DQ3: Sector Erase Timer
Embedded Program Algorithm
Embedded Erase Algorithm
Erase-Suspend-Program
Erase-Suspend-
Read (Note 4)
The device may output a “1” on DQ5 if the system tries to program a “1” to a
location that was previously programmed to “0.” Only an erase operation can
change a “0” back to a “1.” Under this condition, the device halts the operation,
and when the timing limit has been exceeded, DQ5 produces a “1.”
Under both these conditions, the system must write the reset command to return
to the read mode (or to the erase-suspend-read mode if a bank was previously
in the erase-suspend-program mode).
After writing a sector erase command sequence, the system may read DQ3 to de-
termine whether or not erasure has begun. (The sector erase timer does not
apply to the chip erase command.) If additional sectors are selected for erasure,
the entire time-out also applies after each additional sector erase command.
When the time-out period is complete, DQ3 switches from a “0” to a “1.” If the
time between additional sector erase commands from the system can be as-
sumed to be less than 50 µs, the system need not monitor DQ3. See also the
Sector Erase Command Sequence section.
After the sector erase command is written, the system should read the status of
DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure that the device has accepted
the command sequence, and then read DQ3. If DQ3 is “1,” the Embedded Erase
algorithm has begun; all further commands (except Erase Suspend) are ignored
until the erase operation is complete. If DQ3 is “0,” the device will accept addi-
tional sector erase commands. To ensure the command has been accepted, the
system software should check the status of DQ3 prior to and following each sub-
sequent sector erase command. If DQ3 is high on the second status check, the
last command might not have been accepted.
Table 16
Status
shows the status of DQ3 relative to the other status bits.
Erase
Suspended Sector
Non-Erase Suspended
Sector
Table 16. Write Operation Status
Am29BDS320G
P r e l i m i n a r y
(Note 2)
DQ7#
DQ7#
DQ7
Data
0
1
No toggle
Toggle
Toggle
Toggle
DQ6
Data
(Note 1)
DQ5
Data
0
0
0
0
DQ3
Data
N/A
N/A
N/A
1
27243B1 October 1, 2003
(Note 2)
No toggle
Toggle
Toggle
DQ2
Data
N/A