AM79213 Legerity, AM79213 Datasheet - Page 11
![no-image](/images/no-image-200.jpg)
AM79213
Manufacturer Part Number
AM79213
Description
(AM79C203/031 / AM79213) PCM CODEC
Manufacturer
Legerity
Datasheet
1.AM79213.pdf
(48 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
I/O
TSCA, TSCB
Pin Names
IRTA, IRTB
1
, I/O
MCLK
VCCA
VCCD
PCLK
ISUM
IREF
IDIF
RST
I/O
IDC
VIN
INT
2
4
, I/O
3
,
Output, Active
Input, Active
Input/output
Open Drain
Reference
Outputs
Output
Type
Power
Power
Inputs
Input
Input
Input
Input
Input
Low
Low
DC Loop Control Current. The IDC output supplies a current to the ASLIC device for pro-
portional control of the DC loop current flowing through the subscriber loop.
Longitudinal Sense. IDIF is a current input pin fed by the IDIF pin of the ASLIC device.
The current in this pin is used by the ASLAC device for supervisory and diagnostic func-
tions. The IDIF pin has an internal input resistance so an external longitudinal noise filter
capacitor can be connected.
Interrupt. A logic 0 on this pin indicates one or more of the bits in the signaling register
has changed states. An interrupt will be generated when activity is sensed on any signal
in the Signaling Register not masked by the Mask Register. Once an unmasked activity
is sensed, the INT output will be driven Low and held at that state until cleared. See the
description of configuration register 6 for operation.
Control Ports. These control lines are TTL compatible and each can be programmed as
an input or an output. When programmed as inputs, they can monitor external, TTL com-
patible logic circuits. When programmed as outputs, they can control an external logic de-
vice or they can be connected to pin C3, C4, or C5 of the ASLIC device to control test
relay drivers RY1OUT, RY2OUT and RY3OUT (I/O
the Output mode, these pins are controlled by the I/O
Channel Control Register, MPI Command 17.
Current Reference. An external resistor (RREF) connected between this pin and analog
ground generates an accurate on-chip reference current. This current is used by the
ASLAC device in its DC Feed and loop-supervision circuits.
Ring Trip Sense. These pins are current summing nodes referenced to VREF. They pro-
vide terminations for external resistors RSR1 and RSR2, which sense the voltages on
both sides of the ringing feed resistor connected to the ring bus. To determine the ring-
ing current in the loop, the ASLAC device senses the difference between the currents
in these pins.
Metallic Sense. ISUM is a current input pin and is fed by the ISUM pin of the ASLIC de-
vice. The absolute value of the current in this pin is used by the ASLAC device for super-
visory and diagnostic functions.
Master Clock. The master clock is used to operate the digital signal processor. MCLK
can be 2.048 MHz, 4.096 MHz or 8.192 MHz. MCLK may be asynchronous to PCLK.
Upon initialization, the MCLK input is disabled and relevant circuitry is driven by a
connection to PCLK. The MCLK connection may be reestablished under user control.
PCM Clock. The PCM clock determines the rate at which PCM data is serially shifted into
or out of the PCM ports. PCLK is an integer multiple of the frame sync frequency. The
maximum clock frequency is 8.192 MHz and the minimum clock frequency is 128 kHz for
companded data. The minimum clock frequency for linear or companded data plus sig-
naling data is 256 kHz. The PCLK clock may be asynchronous to MCLK if the initial con-
nection state is disabled under user control.
Reset. A logic 0 on this pin resets the ASLAC device to initial default conditions. It is
equivalent to a hardware reset command. A signal less than 100 ns should not cause
a reset. To ensure proper reset, the minimum length of a reset pulse is 50 µs.
Time Slot Control. The time slot control outputs are open drain (requiring an external
pull-up resistor to VCCD) and are normally inactive (high impedance). TSCA is active
(Low) when PCM data is present on DXA, and TSCB is active (Low) when PCM data is
present on DXB. (TSCB and DRB – 44-pin PLCC only.)
Analog Power Supply. VCCA is internally connected to substrate near the analog I/O
section.
Digital Power Supply. VCCD is internally connected to substrate near the digital section.
Analog Input. The analog output (VTX) from the ASLIC device is applied to the ASLAC
device transmit path input, VIN. The signal is sampled, processed, encoded, and trans-
mitted on the PCM Highway.
ASLIC/ASLAC Products
Description
3
, I/O
1
, I/O
4
, 44-pin PLCC version only). In
2
, I/O
3
, and I/O
4
bits in the
11