AT49F001 ATMEL Corporation, AT49F001 Datasheet - Page 2

no-image

AT49F001

Manufacturer Part Number
AT49F001
Description
1-Megabit 128K x 8 5-volt Only Flash Memory
Manufacturer
ATMEL Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AT49F001-12JC
Manufacturer:
ST
Quantity:
5 704
Part Number:
AT49F001-12JC
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT49F001-12JI
Manufacturer:
ATM
Quantity:
5 120
Part Number:
AT49F001-12JI
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT49F001-12PC
Manufacturer:
ATM
Quantity:
5 120
Part Number:
AT49F001-12PI
Manufacturer:
ATM
Quantity:
5 120
Part Number:
AT49F001-12TC
Manufacturer:
ATM
Quantity:
5 120
Part Number:
AT49F001-55JC
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT49F001-55JC
Manufacturer:
ATMEL
Quantity:
1 000
Part Number:
AT49F001-55JC
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
AT49F001-55JI
Manufacturer:
Atmel
Quantity:
10 000
When the device is deselected, the CMOS standby current
is less than 100 A. For the AT49F001NT pin 1 for the DIP
and PLCC packages and pin 9 for the TSOP package are
don’t connect pins.
To allow for simple in-system reprogrammability, the
AT49F001(N)(T) does not require high input voltages for
programming. Five-volt-only commands determine the read
and programming operation of the device. Reading data
out of the device is similar to reading from an EPROM; it
has standard CE, OE, and WE inputs to avoid bus conten-
tion. Reprogramming the AT49F001(N)(T) is performed by
erasing a block of data and then programming on a byte by
byte basis. The byte programming time is a fast 50 s. The
end of a program cycle can be optionally detected by the
DATA polling feature. Once the end of a byte program
cycle has been detected, a new access for a read or pro-
gram can begin. The typical number of program and erase
cycles is in excess of 10,000 cycles.
Block Diagram
2
ADDRESS
INPUTS
RESET
GND
AT49F001(N)(T)
V
WE
OE
CE
CC
Y DECODER
X DECODER
CONTROL
LOGIC
DATA INPUTS/OUTPUTS
DATA LATCHES
INPUT/OUTPUT
MAIN MEMORY
MAIN MEMORY
BOOT BLOCK
PARAMETER
PARAMETER
AT49F001(N)
(64K BYTES)
(32K BYTES)
(16K BYTES)
(8K BYTES)
(8K BYTES)
PROGRAM
Y-GATING
I/O7 - I/O0
BUFFERS
BLOCK 2
BLOCK 1
BLOCK 2
BLOCK 1
The device is erased by executing the erase command
sequence; the device internally controls the erase opera-
tions. There are two 8K byte parameter block sections and
two main memory blocks.
The device has the capability to protect the data in the boot
block; this feature is enabled by a command sequence.
The 16K-byte boot block section includes a reprogramming
lock out feature to provide data integrity. The boot sector is
designed to contain user secure code, and when the fea-
ture is enabled, the boot sector is protected from being
reprogrammed.
In the AT49F001N(T), once the boot block programming
lockout feature is enabled, the contents of the boot block
a r e p e r m a n e n t a n d c a n n o t b e c h a n g e d . I n t h e
AT49F001(T), once the boot block programming lockout
feature is enabled, the contents of the boot block cannot be
changed with input voltage levels of 5.5 volts or less.
8
10000
0FFFF
08000
07FFF
06000
05FFF
04000
03FFF
1FFFF
00000
DATA INPUTS/OUTPUTS
DATA LATCHES
INPUT/OUTPUT
MAIN MEMORY
MAIN MEMORY
AT49F001(N)T
BOOT BLOCK
PARAMETER
PARAMETER
(16K BYTES)
(32K BYTES)
(64K BYTES)
(8K BYTES)
(8K BYTES)
PROGRAM
Y-GATING
I/O7 - I/O0
BUFFERS
BLOCK 1
BLOCK 2
BLOCK 1
BLOCK 2
8
1FFFF
1C000
1BFFF
1A000
19FFF
18000
17FFF
10000
0FFFF
00000

Related parts for AT49F001