CGY181 Siemens Semiconductor Group, CGY181 Datasheet
![no-image](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_sml.jpg)
CGY181
Related parts for CGY181
CGY181 Summary of contents
Page 1
Preliminary Datasheet * Power amplifier for PCN/PCS applications * Fully integrated 2 stage amplifier * Operating voltage range: 2 Overall power added efficiency Input matched simple output match ESD: ...
Page 2
... VG-pin, a positive supply voltage has to be applied to the VD-pins. The VTR-pin has to switched to 0V (GND) during transmit operation. The MMIC CGY181 is self-biased, the operating current is adjusted by the internal control circuit. In receive mode the VTR-pin is not min typ max 0 ...
Page 3
Electrical characteristics ( 25°C , f=1.75 GHz =50 Ohm, VD=3.6V, VG =-4V, VTR pin connected to ground, unless otherwise specified) Characteristics Supply current Pin= 0 dBm Negative supply current (normal operation) Shut-off current ...
Page 4
DC-ID(VG) characteristics - High current Medium current Low current -5 -4,5 -4 DC-Output characteristics - 0,8 0,7 0,6 0,5 0,4 0,3 0,2 0 0,5 1 Pin has to be open during measuring DC-characteristics! ...
Page 5
DC-ID(VG) characteristics - High current Medium current Low current -5 -4,5 -4 DC-Output characteristics - 3 2,5 2 1 0,5 1 Pin has to be open during measuring DC-characteristics! TR Siemens ...
Page 6
V =3.6V =5V Siemens Aktiengesellschaft GaAs MMIC P and PAE vs. ...
Page 7
Output power at different temperatures (V =3.6V Power added efficiency at different temperatures ( ...
Page 8
Output power at different temperatures (V =5V Power added efficiency at ...
Page 9
Measured S-parameter =-4V, VTR connected to ground, pulsed with a duty cycle of 10%, ton=0.33ms -10 -15 -20 1400 1500 Measured S-parameter =-4V, VTR ...
Page 10
V =-4V,f=1.75GHz 2,5 3 Performance of internal bias control circuit @VD=3V (VTR=0V, pulsed with a duty cycle of 10%, ton=0.33ms) 4,0 3,5 3,0 2,5 2,0 1,5 ...
Page 11
Permissible pulse load P Siemens Aktiengesellschaft GaAs MMIC Total Power Dissipation Ptot=f(T tot_max pg. 11/14 CGY 181 ) f(t_p) tot_DC 01.02. ...
Page 12
... CGY181 application board: Layout size is 30mm x 26mm. Principal circuit: VG 1nF VTR (2) Control VTR Circuit 1nF Pin (8) IN Siemens Aktiengesellschaft GaAs MMIC Part Type CGY181 1nF 1nF 1nF 1p2 4µ7 43nH +VD 1nF VG (1) VD1 (7) VD2 (11) GND1 (6, 9) GND2 ( 10) pg. 12/14 ...
Page 13
... PCN Signal Pin=16dBm Generator ROHDE&SCHWARZ SME03 Siemens Aktiengesellschaft GaAs MMIC Pulsed Power Supply VD=3.6V pulsed with a duty cycle of 10% ton=0.577ms VG VD CGY181 OUT IN VTR pg. 13/14 CGY 181 Trigger gate delay 150us gate length 75us Spectrum Analyzer HP 8561E 01.02. ...
Page 14
... I D =1.2A. So the maximum DC - power can be calculated to: This value is smaller than 5W and CW - operation is possible. By decoupling RF power out of the CGY181 the power dissipation of the device can be further reduced. Assuming a power added efficiency PAE the total power dissipation P tot can be calculated using the following formula: ...