ADG741 Analog Devices, ADG741 Datasheet - Page 8

• Manufacturer Part Number: ADG741
• Description: CMOS Low Voltage 2ohm SPST Switches in SC70 Packages
• Manufacturer: Analog Devices

ADG741/ADG742
APPLICATIONS INFORMATION
The ADG741/ADG742 belongs to Analog Devices’ new fam-
ily of CMOS switches. This series of general-purpose switches
have improved switching times, lower on resistance, higher
bandwidth, low power consumption and low leakage currents.
ADG741/ADG742 Supply Voltages
Functionality of the ADG741/ADG742 extends from 1.8 V to
5.5 V single supply, which makes it ideal for battery-powered
instruments, where important design parameters are power
efficiency and performance.
It is important to note that the supply voltage effects the input
signal range, the on resistance, and the switching times of the
part. By looking at the typical performance characteristics
and the specifications, the effects of the power supplies can
be clearly seen.
For V
perature range.
On Response vs. Frequency
Figure 1 illustrates the parasitic components that affect the ac
performance of CMOS switches (the switch is shown surrounded
by a box). Additional external capacitances will further degrade
some performance. These capacitances affect feedthrough,
crosstalk and system bandwidth.
The transfer function that describes the equivalent diagram of
the switch (Figure 1) is of the form (A)s shown below.
where:
C
R
T
T
= C
= R
DD
V
IN
= 1.8 V operation, R
S
LOAD
LOAD
/(R
+ C
LOAD
D
A(s) = R
R
C
+ C
ON
DS
+ R
DS
C
ON
D
T
)




ON
s(R
s(R
is typically 40 Ω over the tem-
ON
C
ON
LOAD
D
C
C
T
DS
R
0.039 (1.00)
0.031 (0.80)
T
) + 1
0.053 (1.35)
0.045 (1.15)
) + 1
R
LOAD
PIN 1
0.004 (0.10)
0.000 (0.00)




Dimensions shown in inches and (mm).
6-Lead Plastic Surface Mount
OUTLINE DIMENSIONS
6
0.087 (2.20)
0.071 (1.80)
1
0.051 (1.30)
V
BSC
OUT
2
5
0.012 (0.30)
0.006 (0.15)
(SC70)
3
4
0.026 (0.65) BSC
0.094 (2.40)
0.071 (1.80)
0.043 (1.10)
0.031 (0.80)
SEATING
PLANE
The signal transfer characteristic is dependent on the switch
channel capacitance, C
zero in the numerator of the transfer function A(s). Because the
switch on resistance is small, this zero usually occurs at high
frequencies. The bandwidth is a function of the switch output
capacitance combined with C
frequency pole corresponding to these capacitances appears in
the denominator of A(s).
The dominant effect of the output capacitance, C
pole breakpoint frequency to occur first. Therefore, in order to
maximize bandwidth a switch must have a low input and output
capacitance and low on resistance. The On Response vs. Fre-
quency plot for the ADG741/ADG742 can be seen in TPC 6.
Off Isolation
Off isolation is a measure of the input signal coupled through an
off switch to the switch output. The capacitance, C
the input signal to the output load, when the switch is off, as
shown in Figure 2.
The larger the value of C
produced. The typical performance characteristic graph of TPC 5
illustrates the drop in off-isolation as a function of frequency. From
dc to roughly 1 MHz, the switch shows better than –75 dB isola-
tion. Up to frequencies of 10 MHz, the off isolation remains better
than –55 dB. As the frequency increases, more and more of the
input signal is coupled through to the output. Off-isolation can be
maximized by choosing a switch with the smallest C
The values of load resistance and capacitance affect off isolation
also, as they contribute to the coefficients of the poles and zeros
in the transfer function of the switch when open.
V
IN
0.007 (0.18)
0.004 (0.10)
S
8
0
C
0.012 (0.30)
0.004 (0.10)
A(s) =
DS
DS
DS
. This capacitance creates a frequency
C
, larger values of feedthrough will be
D



DS
s(R
s(R
and the load capacitance. The
LOAD
LOAD
C
D
LOAD
)(C
C
T
DS
) +1
)
R
LOAD



D
DS
, causes the
DS
as possible.
, couples
V
OUT