HT82K94A HOLTEK [Holtek Semiconductor Inc], HT82K94A Datasheet - Page 18

• Manufacturer Part Number: HT82K94A
• Description: USB Multimedia Keyboard Encoder 8-Bit MCU
• Manufacturer: HOLTEK [Holtek Semiconductor Inc]

Suspend Wake-Up and Remote Wake-Up
If there is no signal on the USB bus for over 3ms, the
HT82K94E/HT82K94A will go into suspend mode. The
Suspend line (bit 0 of the USC) will be set to 1 and a
USB interrupt is triggered to indicate that the
HT82K94E/HT82K94A should jump to the suspend
state to meet the 500 A USB suspend current spec.
In order to meet the 500 A suspend current, the firm-
ware should disable the USB clock by clearing the
USBCKEN (bit3 of the SCC) to 0 . The suspend cur-
rent is 400 A.
User can further decrease the suspend current to 250 A
by setting the SUSP2 (bit4 of the SCC). But if the
SUSP2 is set, user should make sure not to enable the
LVR OPT option, otherwise the HT82K94E/HT82K94A
will be reset.
When the resume signal is sent out by the host, the
HT82K94E/HT82K94A will wake-up the MCUby USB in-
terrupt and the Resume line (bit 3 of the USC) is set. In
order to make the HT82K94E/HT82K94A function prop-
erly, the firmware must set the USBCKEN (bit 3 of the
SCC) to 1 and clear the SUSP2 (bit4 of the SCC).
Since the Resume signal will be cleared before the Idle
signal is sent out by the host, the Suspend line (bit 0 of
the USC) will be set to 0 . So when the MCU is detect-
ing the Suspend line (bit0 of USC), the Resume line
should be remembered and taken into consideration.
After finishing the resume signal, the suspend line will
go inactive and a USB interrupt is triggered. The follow-
ing is the timing diagram.
USB Interface
There are eleven registers, including PIPE_CTRL (41H in bank 1), AWR (address + remote wake-up 42H in bank 1),
STALL (43H in bank 1), PIPE (44H in bank 1), SIES (45H in bank 1), MISC (46H in bank 1), Endpt_EN (47H in bank 1),
FIFO0 (48H in bank 1), FIFO1 (49H in bank 1), FIFO2 (4AH in bank 1) and FIFO3 (4BH in bank 1) used for the USB
function. AWR register contains current address and a remote wake up function control bit. The initial value of AWR is
is completed.
Rev. 1.00
00H . The address value extracted from the USB command is not to be loaded into this register until the SETUP stage
Bit No.
7~1
0
AD6~AD0
WKEN
Label
R/W
W
W
Remote wake-up enable/disable
USB device address
AWR (42H) Register
18
The device with remote wake-up function can wake-up
the USB Host by sending a wake-up pulse through
RMWK (bit 1 of the USC). Once the USB Host receives
a wake-up signal from the HT82K94E/HT82K94A, it will
send a Resume signal to the device. The timing is as fol-
lows:
To Configure the HT82K94E/HT82K94A as PS2 De-
vice
The HT82K94E/HT82K94A can be configured as a USB
interface or PS2 interface device, by configuring the
SPS2 (bit 4 of USR) and SUSB (bit 5 of the USR). If
SPS2=1, and SUSB=0, the HT82K94E/HT82K94A is
configured as a PS2 interface, pin USBD- is configured
as a PS2 Data pin and USBD+ is configured as a PS2
Clk pin. User can easily read or write to the PS2 Data or
PS2 Clk pin by accessing the corresponding bit PS2DAI
(bit 4 of the USC), PS2CKI (bit 5 of the USC), PS2DAO
(bit 6 of the USC) and S2CKO (bit 7 of the USC) respec-
tively.
User should make sure that in order to read the data
properly, the corresponding output bit must be set to 1 .
For example, if it is desired to read the PS2 Data by
reading PS2DAI, the PS2DAO should set to 1 . Other-
wise it is always read as 0 .
If SPS2=0, and SUSB=1, the HT82K94E/HT82K94A is
configured as a USB interface. Both the USBD- and
USBD+ is driven by the SIE of the HT82K94E/
HT82K94A. User can only write or read the USB data
through the corresponding FIFO.
Both SPS2 and SUSB default is 0 .
Function
HT82K94E/HT82K94A
November 22, 2005