RT8004 RICHTEK [Richtek Technology Corporation], RT8004 Datasheet - Page 11

• Manufacturer Part Number: RT8004
• Description: 3A, 4MHz, Synchronous Step-Down Regulator
• Manufacturer: RICHTEK [Richtek Technology Corporation]

This formula has a maximum at V
IRMS = I
commonly used for design because even significant
deviations do not offer much relief. Note that ripple current
ratings from capacitor manufacturers are often based on
only 2000 hours of life which makes it advisable to further
derate the capacitor, or choose a capacitor rated at a higher
temperature than required. Several capacitors may also
be paralleled to meet size or height requirements in the
design.
The selection of C
resistance (ESR) that is required to minimize voltage ripple
and load step transients, as well as the amount of bulk
capacitance that is necessary to ensure that the control
loop is stable. Loop stability can be checked by viewing
the load transient response as described in a later section.
The output ripple, ΔV
The output ripple is highest at maximum input voltage
since
placed in parallel may be needed to meet the ESR and
RMS current handling requirements. Dry tantalum, special
polymer, aluminum electrolytic and ceramic capacitors are
all available in surface mount packages. Special polymer
capacitors offer very low ESR but have lower capacitance
density than other types. Tantalum capacitors have the
highest capacitance density but it is important to only
use types that have been surge tested for use in switching
power supplies. Aluminum electrolytic capacitors have
significantly higher ESR but can be used in cost-sensitive
applications provided that consideration is given to ripple
current ratings and long term reliability. Ceramic capacitors
have excellent low ESR characteristics but can have a
high voltage coefficient and audible piezoelectric effects.
The high Q of ceramic capacitors with trace inductance
can also lead to significant ringing.
Using Ceramic Input and Output Capacitors
Higher values, lower cost ceramic capacitors are now
becoming available in smaller case sizes. Their high ripple
current, high voltage rating and low ESR make them ideal
for switching regulator applications. However, care must
DS8004-03
ΔV
OUT
ΔI
L
increases with input voltage. Multiple capacitors
≤
OUT
ΔI
September 2007
/2. This simple worst-case condition is
L
⎡
⎢
⎣
ESR
OUT
OUT
is determined by the effective series
+
8fC
, is determined by :
1
OUT
⎤
⎥
⎦
IN
= 2V
OUT
, where
be taken when these capacitors are used at the input and
output. When a ceramic capacitor is used at the input
and the power is supplied by a wall adapter through long
wires, a load step at the output can induce ringing at the
input, V
and be mistaken as loop instability. At worst, a sudden
inrush of current through the long wires can potentially
cause a voltage spike at V
part.
Output Voltage Programming
The output voltage is set by an external resistive divider
according to the following equation :
The resistive divider allows the V
of the output voltage as shown in Figure 1.
Frequency Synchronization
The RT8004’ s internal oscillator can be synchronized to
an external clock signal. During synchronization, the top
MOSFET turn-on is locked to the falling edge of the
external frequency source. The synchronization frequency
range is 300kHz to 4MHz. Synchronization only occurs if
the external frequency is greater than the frequency set
by the external resistor. Because slope compensation is
generated by the oscillator’ s RC circuit, the external
frequency should be set 25% higher than the frequency
set by the external resistor to ensure that adequate slope
compensation is present.
Soft-Start
The EN/SS pin provides a means to shut down the RT8004
as well as a timer for soft-start. Pulling the EN/SS pin
below 0.5V places the RT8004 in a low quiescent current
shutdown state (IQ < 1μA).
V
OUT
=
IN
0.8V(1
. At best, this ringing can couple to the output
Figure 1. Setting the Output Voltage
RT8004
+
R2
R1
GND
VFB
)
IN
large enough to damage the
V
OUT
FB
R2
R1
pin to sense a fraction
RT8004
www.richtek.com
11