SP690RCN SIPEX [Sipex Corporation], SP690RCN Datasheet - Page 13

• Manufacturer Part Number: SP690RCN
• Description: 3.0V/3.3V Low Power Microprocessor Supervisory with Battery Switch-Over
• Manufacturer: SIPEX [Sipex Corporation]

The watchdog timer can also initiate a reset.
Refer to the Watchdog Input section.
The SP804T/S/R and SP805T/S/R active-HIGH
RESET output is open drain and the inverse
of the SP690T/S/R and SP802T/S/R RESET
outputs.
RESET is also triggered by a watchdog timeout.
If WDI remains either high or low for a period
that exceeds the watchdog timeout period (1.6
sec), RESET pulses low for 200mS. As long as
RESET is asserted, the watchdog timer remains
cleared. When RESET comes high, the watch-
dog resumes timing and must be serviced within
1.6sec. If WDI is tied high or low, a RESET
pulse is triggered every 1.8sec (t
Reset Threshold
The SP690T and SP805T devices are designed
for 3.3V systems with a 5% power-supply
tolerance and a 10% system tolerance. Except
for watchdog faults, reset will not assert as long
as the power supply remains above 3.15V (3.3V
- 5%). Reset is guaranteed to assert before the
power supply falls below 3.0V.
The SP690S and SP805S devices are designed
for 3.3V
watchdog faults, they are guaranteed not to
assert reset as long as the supply remains above
3.0V (3.3V - 10%). Reset is guaranteed to
assert before the power supply fails below 2.85V
(V
The SP690R and SP805R devices are optimized
for monitoring 3.0V 10% power supplies. Reset
will not occur until V
- 10%), but is guaranteed to occur before the
supply falls below 2.55V (3.0V - 15%).
The SP802T/S/R and SP804T/S/R devices are
respectively similar to the SP690T/S/R and
SP805T/S/R devices with tightened reset
and power-fail threshold tolerances.
SP690T/S/R DS/10
CC
- 14%).
10% power supplies. Except for
SP690T/S/R, 802/T/S/R, 804T/S/R, 805T/S/R Low Power Microprocessor Supervisory
CC
falls below 2.7V (3.0V
WD
plus t
RS
).
13
Watchdog Input
The watchdog circuit monitors the P's activity.
If the P does not toggle the watchdog input
(WDI) within 1.6sec, a reset pulse is triggered.
The internal 1.6sec timer is cleared by either a
reset pulse or by a transition (LOW-to-HIGH or
HIGH-to-LOW) at WDI. If WDI is tied HIGH
or LOW, a RESET pulse is triggered every
1.8sec (t
As long as reset is asserted, the timer remains
cleared and does not count. As soon as reset is
de-asserted, the timer starts counting. Unlike
the 5V SP690A series, the watchdog function
cannot be disabled.
Power-Fail Comparator
The power-fail comparator can be used as an
under-voltage detector to signal the failing of a
power supply (it is completely separate from the
rest of the circuitry and does not need to be
dedicated to this function). The PFI input is
compared to an internal 1.25V. If PFI is less than
V
The power-fail comparator turns off and PFO
goes LOW when V
power-down. The power-fail comparator turns
on as V
comparator is not used, connect PFI to ground
and leave PFO unconnected.
Backup-Battery Switchover
In the event of a brownout or power failure, it
may be necessary to preserve the contents of
RAM. With a backup battery installed at
V
RAM to backup power when V
This family of P supervisors (designed for
3.3V and 3V systems) doesn't always connect
V
than V
a 15
V
PFT
BATTERY
BATTERY
BATTERY
, PFO goes low.
CC
switch) when V
WD
CC
. V
, the devices automatically switch
is greater than V
to V
plus t
crosses V
BATTERY
OUT
RS
).
when V
connects to V
CC
SW
© Copyright 2000 Sipex Corporation
CC
falls below V
on power-up. If the
CC
is below V
BATTERY
.
CC
OUT
fails.
is greater
(through
SW
SW
and
on