X4283 INTERSIL [Intersil Corporation], X4283 Datasheet - Page 7
![no-image](/images/no-image-200.jpg)
X4283
Manufacturer Part Number
X4283
Description
CPU Supervisor with 128K EEPROM
Manufacturer
INTERSIL [Intersil Corporation]
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
X4283
Manufacturer:
XICOR
Quantity:
20 000
Company:
Part Number:
X4283S8I
Manufacturer:
Intersil
Quantity:
3 950
Part Number:
X4283V8-2.7A
Manufacturer:
XICOR
Quantity:
20 000
X4283/85 – Preliminary Information
Table 1. Write Protect Enable Bit and WP Pin Function
Writing to the Control Register
Changing any of the nonvolatile bits of the control reg-
ister requires the following steps:
– Write a 02H to the Control Register to set the Write
– Write a 06H to the Control Register to set both the
– Write a value to the Control Register that has all the
– A read operation occurring between any of the previous
Figure 5. Valid Data Changes on the SDA Bus
REV 1.17 11/27/00
Enable Latch (WEL). This is a volatile operation, so
there is no delay after the write. (Operation preceded
by a start and ended with a stop).
Register Write Enable Latch (RWEL) and the WEL
bit. This is also a volatile cycle. The zeros in the data
byte are required. (Operation preceded by a start
and ended with a stop).
control bits set to the desired state. This can be repre-
sented as 0xys t 01r in binary, where xy are the WD
bits, and rst are the BP bits. (Operation preceded by a
start and ended with a stop). Since this is a nonvola-
tile write cycle it will take up to 10ms to complete. The
RWEL bit is reset by this cycle and the sequence must
be repeated to change the nonvolatile bits again. If bit
2 is set to ‘1’ in this third step (0xys t11r) then the
RWEL bit is set, but the WD1, WD0, BP2, BP1 and
BP0 bits remain unchanged. Writing a second byte to
the control register is not allowed. Doing so aborts the
write operation and returns a NACK.
operations will not interrupt the register write operation.
HIGH
HIGH
LOW
WP
WPEN
X
0
1
SDA
SCL
Memory Array not
Block Protected
Writes OK
Writes OK
Writes OK
Data Stable
Block Protected
Memory Array
Writes Blocked
Writes Blocked
Writes Blocked
www.xicor.com
Data Change
– The RWEL bit cannot be reset without writing to the
To illustrate, a sequence of writes to the device consist-
ing of [02H, 06H, 02H] will reset all of the nonvolatile
bits in the Control Register to 0. A sequence of [02H,
06H, 06H] will leave the nonvolatile bits unchanged
and the RWEL bit remains set.
SERIAL INTERFACE
Serial Interface Conventions
The device supports a bidirectional bus oriented protocol.
The protocol defines any device that sends data onto
the bus as a transmitter, and the receiving device as the
receiver. The device controlling the transfer is called the
master and the device being controlled is called the
slave. The master always initiates data transfers, and
provides the clock for both transmit and receive opera-
tions. Therefore, the devices in this family operate as
slaves in all applications.
Serial Clock and Data
Data states on the SDA line can change only during
SCL LOW. SDA state changes during SCL HIGH are
reserved for indicating start and stop conditions. See
Figure 5.
nonvolatile control bits in the control register, power
cycling the device or attempting a write to a write
protected block.
Block Protect
Writes Blocked
Writes OK
Writes OK
Bits
Data Stable
Characteristics subject to change without notice.
Writes Blocked
WPEN Bit
Writes OK
Writes OK
Protection
Hardware
Software
Software
7 of 22