LMV861MG NSC [National Semiconductor], LMV861MG Datasheet - Page 4

• Manufacturer Part Number: LMV861MG
• Description: 30 MHz Low Power CMOS, EMI Hardened Operational Amplifiers
• Manufacturer: NSC [National Semiconductor]

www.national.com
V
I
I
SR
GBW
Φ
e
i
R
C
THD
n
O
S
Symbol
n
O
OUT
IN
m
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics
Tables.
Note 2: Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC) Field-
Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC).
Note 3: The maximum power dissipation is a function of T
P
Note 4: Electrical table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating
of the device.
Note 5: Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will
also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material.
Note 6: Limits are 100% production tested at 25°C. Limits over the operating temperature range are guaranteed through correlations using statistical quality
control (SQC) method.
Note 7: Number specified is the slower of positive and negative slew rates.
Note 8: The EMI Rejection Ratio is defined as EMIRR = 20log ( V
Note 9: The typical value is calculated by applying absolute value transform to the distribution, then taking the statistical average of the resulting distribution
Note 10: This parameter is guaranteed by design and/or characterization and is not tested in production.
Note 11: The specified limits represent the lower of the measured values for each output range condition.
D
= (T
J(MAX)
Output Swing High,
(measured from V
Output Swing Low,
(measured from V
Output Short Circuit Current
Supply Current
Slew Rate (Note 7)
Gain Bandwidth Product
Phase Margin
Input-Referred Voltage Noise
Input-Referred Current Noise
Closed Loop Output Impedance
Common-Mode Input Capacitance
Differential-Mode Input Capacitance
Total Harmonic Distortion
- T
A
)/ θ
JA
. All numbers apply for packages soldered directly onto a PC board.
Parameter
+
−
)
)
J(MAX)
R
R
R
R
Sourcing, V
V
Sinking, V
V
LMV861
LMV862
A
10% to 90%
f = 1 kHz
f = 100 kHz
f = 1 kHz
f = 20 MHz
f = 1 kHz, A
IN
IN
V
L
L
L
L
, θ
= 2 kΩ to V
= 10 kΩ to V
= 2 kΩ to V
= 10 kΩ to V
= +1, V
= 100 mV
= −100 mV
RF_PEAK
JA
, and T
OUT
OUT
/ΔV
Conditions
OUT
V
A
= 1, BW
. The maximum allowable power dissipation at any ambient temperature is
OS
= V
+
+
= 2V
4
/2
/2
).
+
+
= V
/2
/2
CM
CM
PP
,
,
≥
,
500 kHz
(Note 6)
Min
90
86
90
86
(Note 5)
0.015
2.47
0.02
Typ
150
150
4.9
13
10
20
31
71
60
20
15
3
3
8
5
(Note 6)
Max
2.84
3.27
15
19
14
18
4
5
4
5
nV/
pA/
Units
V/μs
MHz
deg
mV
mV
mA
mA
pF
%
Ω