BD8624EFV ROHM [Rohm], BD8624EFV Datasheet
BD8624EFV
Related parts for BD8624EFV
BD8624EFV Summary of contents
Page 1
... DC/DC converters BD8628EFV, BD8624EFV ●Description BD8628EFV / BD8624EFV have realized the high performance and reliability required as a power supply for thin-screen TV. With built-in FET 1ch current mode control, the DC/DC Converter series has the advantage of high-speed load response and wide phase margin. Due to the high-speed load response most suitable for TV-purpose processors with increasingly high performance, and due to the wide phase margin it leaves a good margin for board pattern & ...
Page 2
Electric characteristic (Ta=25℃, VCC=6.5V, GND=0V,CTL=6.5V unless otherwise specified.) Parameter Circuit current 1 Circuit current 2 < Error amplifier part > Standard voltage （VREF） Terminal FB Input bias current Terminal FC Clamping voltage H Terminal FC Clamping voltage L Terminal ...
Page 3
Permissible loss This package is a product of which the feature is the high heat radiation, and connect the back to GND based on recommended land pattern when you mount. T θ jc θ ℃ /W] [ ℃ ...
Page 4
Block diagram RT RSET PDET PIO CTL VCC PVCC PVCC TEST2 TEST1 N.C. N.C. ● Terminal explanation No. Symbol 1 PGND Power GND terminal 2 PGND Power GND terminal No wire connection. 3 N.C. (Connect to GND ...
Page 5
Terminal equivalent circuit chart Terminal Terminal No. name Power GND 1 (The same potential as the GND PGND terminal) Power GND 2 (The same potential as the GND PGND terminal terminal terminal High ...
Page 6
Terminal Terminal No. name 11 FB Voltage detection terminal Soft start adjustment capacity connection 12 SS terminal Frequency adjustment resistance connection 13 RT terminal Off latch effective time adjustment resistance 14 RSET terminal 15 PDET Error state notification terminal Terminal ...
Page 7
Terminal Terminal No. name Error state notification and external IC error 16 PIO detection terminal 17 CTL Enable input 21 TEST2 Test terminal (Connect to GND TEST1 Test terminal (Connect to GND PVCC Power VCC terminal ...
Page 8
Operation description ON/OFF control DC/DC converter ON/OFF function DC/DC converter controller can be controlled ON/OFF by CTL terminal. Analog circuit starts operation at ON control (on mode), and goes down to setting output voltage. Analog circuit should be standby ...
Page 9
OSC oscillation frequency setting function SW output oscillation frequency of DC/DC converter can be set by installing resistance between RT terminal and GND externally. 10000 1000 100 10 1 Range of terminal RT connection resistance setting 23kΩ≦Rrt≦135kΩ （100kHz≦fosc≦600kHz） ...
Page 10
PROTECT BUS Input/output function The terminal PIO is PROTECT BUS Input/output terminal. The terminal PIO is Hi-Z when DC/DC usually operates. When the terminal PIO becomes LOW by connecting PROTECT BUS, DC/DC is turned off. Afterwards, when the terminal PIO ...
Page 11
Protection function Protection circuit is effective for destruction prevention due to accident so that avoid using by continuous protection operation. Low voltage protection function(LVP) Low voltage protection function detects set output voltage V compared to internal reference level. Low ...
Page 12
Overcurrent protection function (OCP) Overcurrent protection function compared drain voltage (LX terminal voltage) with internal OCP terminal voltage when internal Nch POWER MOS is ON. When LX terminal voltage becomes lower than OCP terminal voltage, external MOS would be OFF. ...
Page 13
Soft start time-out function DC/DC converter off-latch-controls when V passed from soft start. Error detection (off latch) release method DC/DC converter becomes off latch condition when protection function operates. Off latch can be released by the following method. DC/DC converter ...
Page 14
HTSSOP-B24 <Dimension> 7.8 ± 0 − +0.05 0.17 0.325 −0.03 0.08 S 0.65 +0.05 0.2 −0.04 0.08 M （Unit:mm) <Tape and Reel information> Tape Embossed carrier tape Quantity 2000pcs Direction E2 of feed (The ...
Page 15
Appendix No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product ...