LT3029 LINER [Linear Technology], LT3029 Datasheet - Page 11
![no-image](/images/no-image-200.jpg)
LT3029
Manufacturer Part Number
LT3029
Description
Dual 500mA/500mA Low Dropout, Low Noise, Micropower Linear Regulator
Manufacturer
LINER [Linear Technology]
Datasheet
1.LT3029.pdf
(20 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LT3029EDE
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
LT3029EDE#PBF
Manufacturer:
LT
Quantity:
197
Part Number:
LT3029EDE#TRPBF
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
LT3029EMSE
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
LT3029EMSE#PBF
Manufacturer:
LT
Quantity:
2 144
Part Number:
LT3029EMSE#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT3029EMSE#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LT3029HDE
Manufacturer:
LT
Quantity:
10 000
PIN FUNCTIONS
BYP1/BYP2 (Pin 1/Pin 8): Bypass. Use the BYP1/BYP2
pins to bypass the reference of the LT3029 regulator and
achieve low output noise performance. Internal circuitry
clamps the BYP1/BYP2 pins to ±0.6V (one V
ground. A small capacitor from the corresponding output
to this pin bypasses the reference to lower the output
voltage noise. Using a maximum value of 10nF reduces
the output voltage noise to a typical 20μV
to 100kHz bandwidth. If not used, this pin must be left
unconnected.
NC (Pin 2): No Connect. This pin is not connected to
any internal circuitry. It may be fl oated, tied to V
to GND.
OUT1/OUT2 (Pins 3, 4/Pins 6, 7): Output. The outputs
supply power to the loads. A minimum 3.3μF output ca-
pacitor prevents oscillations on each output. Applications
with large output load transients require larger values of
output capacitance to limit peak voltage transients. See
the Applications Information section for more on output
capacitance and reverse output characteristics.
GND (Pin 5, 17): Ground. The exposed pad (Pin 17) of
the DFN and MSOP packages is an electrical connection
to GND. To ensure proper electrical and thermal perfor-
mance, solder Pin 17 to the PCB ground and tie directly
to Pin 5. Connect the bottom of the output voltage setting
resistor divider directly to GND (Pin 5) for optimum load
regulation performance.
IN1/IN2 (Pins 13, 14/Pins 11, 12): Inputs. The IN1/IN2
pins supply power to each channel. The LT3029 requires
a bypass capacitor at the IN1/IN2 pins if located more
than six inches away from the main input fi lter capacitor.
RMS
over a 10Hz
BE
IN
) from
or tied
SHDN1 or SHDN2 pin low puts its corresponding LT3029
channel into a low power state and turns its output off. The
SHDN1 and SHDN2 pins are completely independent of
each other, and each SHDN pin only affects operation on
its corresponding channel. Drive the SHDN1 and SHDN2
pins with either logic or an open collector/drain with pull-up
resistors. The resistors supply the pull-up current to the
open collectors/drains and the SHDN1 or SHDN2 current,
typically less than 1μA. If unused, connect the SHDN1 and
SHDN2 to their corresponding IN pins. Each channel will
be in its low power shutdown state if its corresponding
SHDN pin is not connected.
ADJ1/ADJ2: (Pin 16/Pin 9) Adjust Pin. These are the error
amplifi er inputs. These pins are internally clamped to ±9V.
A typical input bias current of 30nA fl ows into the pins
(see curve of ADJ1/ADJ2 Pin Bias Current vs Temperature
in the Typical Performance Characteristics section). The
ADJ1 and ADJ2 pin voltage is 1.215V referenced to ground
and the output voltage range is 1.215V to 19.5V.
Include a bypass capacitor in battery-powered circuits,
as a battery’s output impedance rises with frequency. A
bypass capacitor in the range of 1μF to 10μF suffi ces. The
LT3029’s design withstands reverse voltages on the IN pins
with respect to ground and the OUT pins. In the case of
a reversed input, which occurs if a battery is plugged in
backwards, the LT3029 acts as if a diode is in series with
its input. No reverse current fl ows into the LT3029 and no
reverse voltage appears at the load. The device protects
itself and the load.
SHDN1 / SHDN2 (Pin 15/Pin 10): Shutdown. Pulling the
LT3029
11
3029f