ADP3415LRM-REEL AD [Analog Devices], ADP3415LRM-REEL Datasheet - Page 3

• Manufacturer Part Number: ADP3415LRM-REEL
• Description: Dual MOSFET Driver with Bootstrapping
• Manufacturer: AD [Analog Devices]

ABSOLUTE MAXIMUM RATINGS*
VCC to GND . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
BST to GND . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +30 V
BST to SW . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
SW to GND . . . . . . . . . . . . . . . . . . . . . . . . . –2.0 V to +25 V
SD, IN, DRVLSD to GND . . . . . . . . . . . . . . –0.3 V to +7.3 V
Operating Ambient Temperature Range . . . . . . 0°C to 100°C
Operating Junction Temperature Range . . . . . . 0°C to 125°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . . 300°C
*Stresses above those listed under Absolute Maximum Ratings may cause perma-
Pin No.
1
2
3
4
5
6
7
8
9
10
Model
ADP3415LRM-REEL
ADP3415LRM-REEL7
ADP3415LRMZ-REEL*
*Z = Pb-free part.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although the
ADP3415 features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended
to avoid performance degradation or loss of functionality.
REV. B
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability. Absolute maximum
ratings apply individually only, not in combination. Unless otherwise specified, all
other voltages are referenced to GND.
JA
JC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155°C/W
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40°C/W
Mnemonic
IN
SD
DRVLSD
DLY
VCC
DRVL
GND
SW
DRVH
BST
Function
TTL-Level Input Signal. Has primary control of the drive outputs.
Shutdown. When high, this pin enables normal operation. When low, DRVH and DRVL are forced low
and the supply current (I
Drive-Low Shutdown. When DRVLSD is low, DRVL is kept low. When DRVLSD is high, DRVL is
enabled and controlled by IN and by the adaptive OPC function.
High-Side Turn-On Delay. A resistor from this pin to ground programs an extended delay from turn-off
of the lower FET to turn-on of the upper FET.
Input Supply. This pin should be bypassed to GND with a ~10 µF ceramic capacitor.
Synchronous Rectifier Drive. Output drive for the lower (synchronous rectifier) FET.
Ground. Should be directly connected to the ground plane, close to the source of the lower FET.
This pin should be connected to the buck switching node, close to the upper FET’s source. It is the
floating return for the upper FET drive signal. Also, it is used to monitor the switched voltage for the
OPC function.
Buck Drive. Output drive for the upper (buck) FET.
Floating Bootstrap Supply for the Upper FET. A capacitor connected between BST and SW pins holds
this bootstrapped supply voltage for the high-side FET driver as it is switched. The capacitor should be
an MLC type and should have substantially greater capacitance (e.g., ~ 20×) than the input capacitance
of the upper FET.
Temperature
Guide
0°C to 100°C
0°C to 100°C
0°C to 100°C
PIN FUNCTION DESCRIPTIONS
CCQ
Package
Description
MSOP
MSOP
MSOP
ORDERING GUIDE
) is minimized as specified.
–3–
Package
Option
RM-10
RM-10
RM-10
DRVLSD
PIN CONFIGURATION
VCC
DLY
SD
IN
1
2
3
4
5
(Not to Scale)
ADP3415
TOP VIEW
Quantity
per Reel
3,000
1,000
3,000
10
9
8
7
6
BST
DRVH
SW
GND
DRVL
ADP3415
Branding
P1E
P1E
P1E