W25Q80BVDAAG WINBOND [Winbond], W25Q80BVDAAG Datasheet - Page 38
![no-image](/images/no-image-200.jpg)
W25Q80BVDAAG
Manufacturer Part Number
W25Q80BVDAAG
Description
8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
Manufacturer
WINBOND [Winbond]
Datasheet
1.W25Q80BVDAAG.pdf
(75 pages)
- Current page: 38 of 75
- Download datasheet (2Mb)
9.2.19
The “Continuous Read Mode” bits are used in conjunction with “Fast Read Dual I/O”, “Fast Read Quad
I/O”, “Word Read Quad I/O” and “Octal Word Read Quad I/O” instructions to provide the highest random
Flash memory access rate with minimum SPI instruction overhead, thus allow true XIP (execute in place)
to be performed on serial flash devices.
M7-0 need to be set by the Dual/Quad I/O Read instructions. M5-4 are used to control whether the 8-bit
SPI instruction code (BBh, EBh, E7h or E3h) is needed or not for the next command. When M5-4 = (1,0),
the next command will be treated same as the current Dual/Quad I/O Read command without needing
the 8-bit instruction code; when M5-4 do not equal to (1,0), the device returns to normal SPI mode, all
commands can be accepted. M7-6 and M3-0 are reserved bits for future use, either 0 or 1 values can be
used.
9.2.20
Continuous Read Mode Reset instruction can be used to set M4 = 1, thus the device will release the
Continuous Read Mode and return to normal SPI operation, as shown in figure 18.
Since W25Q80BV does not have a hardware Reset pin, so if the controller resets while W25Q80BV is set
to Continuous Mode Read, the W25Q80BV will not recognize any initial standard SPI instructions from
the controller. To address this possibility, it is recommended to issue a Continuous Read Mode Reset
instruction as the first instruction after a system Reset. Doing so will release the device from the
Continuous Read Mode and allow Standard SPI instructions to be recognized.
To reset “Continuous Read Mode” during Quad I/O operation, only eight clocks are needed. The
instruction is “FFh”. To reset “Continuous Read Mode” during Dual I/O operation, sixteen clocks are
needed to shift in instruction “FFFFh”.
CLK
/CS
IO
IO
IO
IO
Continuous Read Mode Bits (M7-0)
Continuous Read Mode Reset (FFh or FFFFh)
0
1
2
3
Mode 3
Mode 0
Figure 18. Continuous Read Mode Reset for Fast Read Dual/Quad I/O
0
1
for Quad I/O (FFh)
Mode Bit Reset
2
3
4
5
6
- 38 -
Don't Care
Don't Care
Don't Care
7
8
9
10
for Dual I/O (FFFFh)
Mode Bit Reset
11
12
13
14
W25Q80BV
15
Mode 3
Mode 0
Related parts for W25Q80BVDAAG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![w25q80bv](/images/no-image3.png)
Part Number:
Description:
8m-bit Serial Flash Memory With Dual And Quad Spi
Manufacturer:
Winbond Electronics Corp America
Datasheet:
![W83697HF](/images/manufacturer_photos/0/7/712/winbond_tmb.jpg)
Part Number:
Description:
WINBOND I/O, UART, infrared, parallel port, game port, MIDI port, flash ROM interface, general purpose I/O ports, FDC, hardware monitor functions
Manufacturer:
Winbond
Datasheet:
![W91444](/images/manufacturer_photos/0/7/712/winbond_tmb.jpg)
Part Number:
Description:
13-MEMORY TONE/PULSE DIALER WITH SAVE FUNCTION
Manufacturer:
Winbond
Datasheet:
![WE9192G](/images/manufacturer_photos/0/7/712/winbond_tmb.jpg)
Part Number:
Description:
TOUCH PULSE DIALER WITH REDIAL
Manufacturer:
Winbond
Datasheet:
![W91216](/images/manufacturer_photos/0/7/712/winbond_tmb.jpg)
Part Number:
Description:
Tone/pulse dialer with redial function
Manufacturer:
Winbond
Datasheet:
![WE9192B](/images/manufacturer_photos/0/7/712/winbond_tmb.jpg)
Part Number:
Description:
TOUCH PULSE DIALER WITH REDIAL
Manufacturer:
Winbond
Datasheet:
![W91351](/images/manufacturer_photos/0/7/712/winbond_tmb.jpg)
Part Number:
Description:
DTMF Transmitter, 3.58MHz, 5V, Standby, CMOS, 18-PDIP
Manufacturer:
Winbond
Datasheet:
![W55206B](/images/manufacturer_photos/0/7/712/winbond_tmb.jpg)
Part Number:
Description:
SERIAL VOICE SRAM (128K · 1 BIT)
Manufacturer:
Winbond
Datasheet:
![W91350](/images/manufacturer_photos/0/7/712/winbond_tmb.jpg)
Part Number:
Description:
DTMF Transmitter, 3.58MHz, 5V, Standby, CMOS, 18-PDIP
Manufacturer:
Winbond
Datasheet:
![W91446](/images/manufacturer_photos/0/7/712/winbond_tmb.jpg)
Part Number:
Description:
13-MEMORY TONE/PULSE DIALER WITH SAVE FUNCTION
Manufacturer:
Winbond
Datasheet:
![WE9142A](/images/manufacturer_photos/0/7/712/winbond_tmb.jpg)
Part Number:
Description:
WE9142ATone/Pulse Telephone Dialer
Manufacturer:
Winbond
Datasheet:
![W91433](/images/manufacturer_photos/0/7/712/winbond_tmb.jpg)
Part Number:
Description:
13 Memory Tone / Pulse Switchable Dialer with Save Function
Manufacturer:
Winbond
Datasheet:
![W91473D](/images/manufacturer_photos/0/7/712/winbond_tmb.jpg)
Part Number:
Description:
14-memory tone/pulse switchable dialer with handfree and lock functions
Manufacturer:
Winbond
Datasheet:
![W91442N](/images/manufacturer_photos/0/7/712/winbond_tmb.jpg)
Part Number:
Description:
10-memory tone/pulse dialer with save function
Manufacturer:
Winbond
Datasheet:
![W91F810N](/images/manufacturer_photos/0/7/712/winbond_tmb.jpg)
Part Number:
Description:
23-flash memory tone/pulse dialer with handfree, lock and hold functions
Manufacturer:
Winbond
Datasheet: