AT88SC0808C ATMEL [ATMEL Corporation], AT88SC0808C Datasheet - Page 6
![no-image](/images/no-image-200.jpg)
AT88SC0808C
Manufacturer Part Number
AT88SC0808C
Description
CryptoMemory 8 Kbit
Manufacturer
ATMEL [ATMEL Corporation]
Datasheet
1.AT88SC0808C.pdf
(14 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AT88SC0808C
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
AT88SC0808C-SI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
AT88SC0808C-U
Manufacturer:
3COM
Quantity:
500
Part Number:
AT88SC0808C-U
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
AT88SC0808CA
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
AT88SC0808CA-SH-T
Manufacturer:
PANASONIC
Quantity:
1 000
Part Number:
AT88SC0808CA-SU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Communication
Security Modes
Table 4. Communication Security Modes
Note:
Security Options
Anti-tearing
Write Lock
6
Mode
Standard
Authentication
Encryption
11011001
$080
1. Configuration data include viewable areas of the Configuration Zone except the passwords:
AT88SC0808C
MDC: Modification Detection Code.
MAC: Message Authentication Code.
xxxx xxxx
locked
$081
Configuration Data
xxxx xxxx
locked
$082
Clear
Clear
Clear
Communications between the device and host operate in three basic modes. Standard
mode is the default mode for the device after power-up. Authentication mode is acti-
vated by a successful authentication sequence. Encryption mode is activated by a
successful encryption activation following a successful authentication.
In the event of a power loss during a write cycle, the integrity of the device’s stored data
may be recovered. This function is optional: the host may choose to activate the anti-
tearing function, depending on application requirements. When anti-tearing is active,
write commands take longer to execute, since more write cycles are required to com-
plete them, and data are limited to eight bytes.
Data are written first to a buffer zone in EEPROM instead of the intended destination
address, but with the same access conditions. The data are then written in the required
location. If this second write cycle is interrupted due to a power loss, the device will
automatically recover the data from the system buffer zone at the next power-up.
In 2-wire mode, the host is required to perform ACK polling for up to 20 ms after write
commands when anti-tearing is active. At power-up, the host is required to perform ACK
polling, in some cases for up to 10 ms, in the event that the device needs to carry out the
data recovery process.
If a user zone is configured in the write lock mode, the lowest address byte of an 8-byte
page constitutes a write access byte for the bytes of that page.
Example: The write lock byte at $080 controls the bytes from $080 to $087.
The write lock byte may also be locked by writing its least significant (rightmost) bit to
“0”. Moreover, when write lock mode is activated, the write lock byte can only be pro-
grammed – that is, bits written to “0” cannot return to “1”.
In the write lock configuration, only one byte can be written at a time. Even if several
bytes are received, only the first byte will be taken into account by the device.
(1)
xxxx xxxx
$083
xxxx xxxx
User Data
Encrypted
$084
Clear
Clear
xxxx xxxx
locked
$085
Passwords
Encrypted
Encrypted
xxxx xxxx
Clear
$086
xxxx xxxx
$087
Data Integrity Check
2024DS–SMEM–04/03
MDC
MAC
MAC
$80
@