93C66A MICROCHIP [Microchip Technology], 93C66A Datasheet - Page 4
![no-image](/images/no-image-200.jpg)
93C66A
Manufacturer Part Number
93C66A
Description
4K 5.0V Automotive Temperature Microwire Serial EEPROM
Manufacturer
MICROCHIP [Microchip Technology]
Datasheet
1.93C66A.pdf
(12 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
93C66A
Manufacturer:
PHILIPS
Quantity:
17 347
Part Number:
93C66A
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
93C66A-E/SN
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
93C66A-I/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
93C66A-SU27
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
93C66ALMB
Manufacturer:
FAIRCHILD/仙童
Quantity:
20 000
93C66A/B
3.0
Instructions, addresses, and write data are clocked into
the DI pin on the rising edge of the clock (CLK). The DO
pin is normally held in a HIGH-Z state except when
reading data from the device, or when checking the
READY/BUSY status during a programming operation.
The READY/BUSY status can be verified during an
ERASE/WRITE operation by polling the DO pin; DO
low indicates that programming is still in progress, while
DO high indicates the device is ready. The DO will enter
the HIGH-Z state on the falling edge of the CS.
3.1
The START bit is detected by the device if CS and DI
are both high with respect to the positive edge of CLK
for the first time.
Before a START condition is detected, CS, CLK, and DI
may change in any combination (except to that of a
START condition), without resulting in any device oper-
ation (ERASE, ERAL, EWDS, EWEN, READ, WRITE,
and WRAL). As soon as CS is high, the device is no
longer in the standby mode.
An instruction following a START condition will only be
executed if the required amount of opcodes,
addresses, and data bits for any particular instruction is
clocked in.
After execution of an instruction (i.e., clock in or out of
the last required address or data bit) CLK and DI
become don't care bits until a new START condition is
detected.
FIGURE 3-1:
DS21207B-page 4
(PROGRAM)
Note:
(READ)
FUNCTIONAL DESCRIPTION
START Condition
CLK
DO
DO
CS
DI
AC Test Conditions: V
V
V
V
V
V
V
V
V
V
V
OL
OH
OL
OH
IH
IH
IL
IL
IH
IL
SYNCHRONOUS DATA TIMING
T
T
DIS
SV
T
CSS
IL
= 0.4V, V
IH
T
CKH
T
= 2.4V.
T
PD
DIH
Preliminary
3.2
It is possible to connect the Data In (DI) and Data
Out (DI) pins together. However, with this configuration
it is possible for a “bus conflict” to occur during the
“dummy zero” that precedes the READ operation, if A0
is a logic-high level. Under such a condition the voltage
level seen at DO is undefined and will depend upon the
relative impedances of DO and the signal source driv-
ing A0. The higher the current sourcing capability of A0,
the higher the voltage at the DO pin.
3.3
During power-up, all programming modes of operation
are inhibited until V
3.8V. During power-down, the source data protection
circuitry acts to inhibit all programming modes when
Vcc has fallen below 3.8V at nominal conditions.
The ERASE/WRITE Disable (EWDS) and ERASE/
WRITE Enable (EWEN) commands give additional pro-
tection against accidentally programming during nor-
mal operation.
After power-up, the device is automatically in the
EWDS mode. Therefore, an EWEN instruction must be
performed before any ERASE or WRITE instruction
can be executed.
STATUS VALID
T
CKL
Data In (DI) and Data Out (DO)
Data Protection
CC
has reached a level greater than
T
1998 Microchip Technology Inc.
PD
T
T
T
CZ
CZ
CSH