24C01CT-E/P MICROCHIP [Microchip Technology], 24C01CT-E/P Datasheet
24C01CT-E/P
Related parts for 24C01CT-E/P
24C01CT-E/P Summary of contents
Page 1
... The Microchip Technology Inc. 24C01C bit Serial Electrically Erasable PROM with a voltage range of 4.5V to 5.5V. The device is organized as a single block of 128 x 8-bit memory with a 2-wire serial interface. Low-current design permits operation with typical standby and active currents of only 10 μA and 1 mA, respectively ...
Page 2
ELECTRICAL CHARACTERISTICS (†) Absolute Maximum Ratings V .............................................................................................................................................................................7.0V CC All inputs and outputs w.r.t. V ......................................................................................................... -0. Storage temperature ...............................................................................................................................-65°C to +150°C Ambient temperature with power applied ................................................................................................-40°C to +125°C ESD protection on all pins ...
Page 3
TABLE 1-2: AC CHARACTERISTICS All parameters apply across the specified operating ranges unless otherwise noted. Parameter Symbol Clock frequency F CLK Clock high time T HIGH Clock low time T LOW SDA and SCL rise time T R SDA and ...
Page 4
PIN DESCRIPTIONS 2.1 SDA Serial Data This is a bidirectional pin used to transfer addresses and data into and data out of the device open drain terminal, therefore the SDA bus requires a pull-up resistor ...
Page 5
BUS CHARACTERISTICS The following bus protocol has been defined: • Data transfer may be initiated only when the bus is not busy. • During data transfer, the data line must remain stable whenever the clock line is high. Changes ...
Page 6
DEVICE ADDRESSING A control byte is the first byte received following the Start condition from the master device (Figure 5-1). The control byte consists of a four-bit control code; for the 24C01C this is set as ‘1010’ binary ...
Page 7
... Address Pointer of the 24C01C. After receiving another Acknowledge signal from the 24C01C the master device will transmit the data word to be written into the addressed memory location. The 24C01C acknowledges again and the master gener- ates a Stop condition. This initiates the internal write cycle, and during this time the 24C01C will not generate Acknowledge signals (Figure 6-1) ...
Page 8
ACKNOWLEDGE POLLING Since the device will not acknowledge during a write cycle, this can be used to determine when the cycle is complete (this feature can be used to maximize bus throughput). Once the Stop condition for a ...
Page 9
... To provide sequential reads the 24C01C contains an internal Address Pointer which is incremented by one at the completion of each operation. This Address Pointer allows the entire memory contents to be serially read during one operation. The internal Address Pointer will automatically roll over from address 7F to address 00 ...
Page 10
FIGURE 8-3: SEQUENTIAL READ Bus Activity Control Master Byte SDA Line Bus Activity DS21201G-page 10 Data n Data Data Data n + ...
Page 11
PACKAGING INFORMATION 9.1 Package Marking Information 8-Lead PDIP (300 mil) XXXXXXXX T/XXXNNN YYWW 8-Lead SOIC (3.90 mm) XXXXXXXT XXXXYYWW NNN 8-Lead TSSOP XXXX TYWW NNN 8-Lead MSOP XXXXT YWWNNN 8-Lead 2x3 DFN XXX YWW NN © 2007 Microchip Technology ...
Page 12
Part Number TSSOP 24C01C 4C1C Note Temperature grade (I, E) Legend: XX...X Part number or part number code T Temperature ( Year code (last digit of calendar year) YY Year code (last 2 digits of ...
Page 13
Plastic Dual In-Line (P or PA) – 300 mil Body [PDIP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging N NOTE Number of Pins Pitch ...
Page 14
Plastic Small Outline (SN or OA) – Narrow, 3.90 mm Body [SOIC] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging N NOTE Number of Pins ...
Page 15
Plastic Thin Shrink Small Outline (ST) – 4.4 mm Body [TSSOP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging N NOTE Number of Pins Pitch ...
Page 16
Plastic Micro Small Outline Package (MS or UA) [MSOP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D N NOTE Number of Pins ...
Page 17
Plastic Dual Flat, No Lead Package (MC) – 2x3x0.9 mm Body [DFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D N NOTE TOP VIEW A3 Number of ...
Page 18
APPENDIX A: REVISION HISTORY Revision D Corrections to Section 1.0, Electrical Characteristics. Revision E Added DFN package. Revision F (01/2007) Revised Features Section; Deleted Commercial Temp; Replaced Package Drawings; Replaced On-Line Support page; Revised Product ID System. Revision G ...
Page 19
THE MICROCHIP WEB SITE Microchip provides online support via our WWW site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web ...
Page 20
READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip prod- uct. If you wish to provide your comments on organization, clarity, subject matter, and ways in which ...
Page 21
... To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office PART NO. X /XX Device Temperature Package Range 2 Device: 24C01C Serial EEPROM 2 24C01CT Serial EEPROM (Tape and Reel) Temperature I = -40°C to +85°C Range -40°C to +125°C Package Plastic DIP (300 mil Body), 8-lead ...
Page 22
NOTES: DS21201G-page 22 © 2007 Microchip Technology Inc. ...
Page 23
... SmartShunt are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. OR AmpLab, FilterLab, Linear Active Thermistor, Migratable INFORMATION, Memory, MXDEV, MXLAB, PS logo, SEEVAL, SmartSensor and The Embedded Control Solutions Company are OR registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM ...
Page 24
W ORLDWIDE AMERICAS ASIA/PACIFIC Corporate Office Asia Pacific Office 2355 West Chandler Blvd. Suites 3707-14, 37th Floor Chandler, AZ 85224-6199 Tower 6, The Gateway Tel: 480-792-7200 Habour City, Kowloon Fax: 480-792-7277 Hong Kong Technical Support: Tel: 852-2401-1200 http://support.microchip.com Fax: 852-2401-3431 ...