MAX849 MAXIM [Maxim Integrated Products], MAX849 Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
MAX849
Manufacturer Part Number
MAX849
Description
1-Cell to 3-Cell, High-Power, Low-Noise, Step-Up DC-DC Converters
Manufacturer
MAXIM [Maxim Integrated Products]
Datasheet
1.MAX849.pdf
(16 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX849ESE
Manufacturer:
MAXIM
Quantity:
32
Company:
Part Number:
MAX849ESE
Manufacturer:
MAX
Quantity:
13 130
Part Number:
MAX849ESE
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX849ESE-T
Manufacturer:
MAXIM
Quantity:
20 000
Part Number:
MAX849ESE-T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX849TG074
Manufacturer:
INTERSIL
Quantity:
2 778
1-Cell to 3-Cell, High-Power,
Low-Noise, Step-Up DC-DC Converters
8
PIN
10
11
12
13
14
15
16
1
_______________________________________________________________________________________
2
3
4
5
6
7
8
9
CLK/SEL
AINSEL
NAME
POKIN
PGND
POUT
DATA
AIN2
GND
AIN1
OUT
POK
ON2
ON1
REF
FB
LX
ADC’s Channel 1 Input. Analog input voltage range is 0.625V to 1.875V.
ADC’s Channel 2 Input. Analog input voltage range is 0V to 2.5V.
Reference Output. Bypass with a 0.22µF capacitor to GND.
Ground. Use for low-current ground paths. Connect to PGND with a short trace.
Output Sense Input. The IC is powered from OUT. Bypass to GND with a 0.1µF ceramic capacitor. Connect
OUT to POUT through a 10Ω series resistor.
Power-Good Comparator Input. Connect to GND for fixed threshold (V
connect to a resistor divider from OUT to GND.
Dual Mode DC-DC Converter Feedback Input. Connect to GND for fixed 3.3V output voltage. Connect to
a resistor divider from OUT to GND to adjust the output voltage. Minimize noise coupling from switching
signals to FB.
Power-Good Output. This open-drain output is pulled low when the output voltage (V
the internally set threshold (fixed threshold), or when the voltage at POKIN drops below V
threshold).
ADC’s Input Channel Selector. Pull low to select AIN1 and drive high to select AIN2.
ADC’s Serial Output. Pulsed output, RZ format. Full scale is f
DATA output is low when V
External Clock Input/Regulator’s Switching Mode Selector.
CLK/SEL = low: low-power, low-quiescent PFM mode. Delivers 100mW of output power.
CLK/SEL = high: low-noise, high-power PWM mode, switching at a constant frequency (300kHz).
CLK/SEL = driven with external clock: low-noise, high-power, synchronized PWM mode. The internal
oscillator is synchronized to the external clock (200kHz ~ 400kHz). Turning the DC-DC converter on with
V
nominal value.
Source of the Internal N-Channel Power MOSFET. Connect to high-current ground path.
Drain of the Internal N-Channel Power MOSFET and P-Channel Synchronous Rectifier
Source of the Internal P-Channel Synchronous Rectifier MOSFET. Connect an external Schottky diode from
LX to POUT. Bypass to PGND with a 0.1µF ceramic capacitor as close to the IC as possible.
OFF Control Input. When ON1 = 0 and ON2 = 1, the IC is off.
ON Control Input. When ON1 = 1 or ON2 = 0, the IC is on.
CLK/SEL
= 0V also serves as a soft-start function, since the peak inductor current is limited to 30% of the
CLK/SEL
= 0V (PFM mode).
FUNCTION
OSC
/2 ( f
CLK
OUT
/2 in external sync mode). The
x 0.9). To adjust the threshold,
Pin Description
OUT
) drops below
REF
(adjustable