EL5176 INTERSIL [Intersil Corporation], EL5176 Datasheet
EL5176
Available stocks
Related parts for EL5176
EL5176 Summary of contents
Page 1
... Generally, this pin is grounded but it can be tied to any voltage reference. Both outputs (OUT+, OUT-) are short-circuit protected to withstand temporary overload condition. The EL5176 is available in the 10 Ld MSOP package and is specified for operation over the full -40°C to +85°C temperature range. See also EL5171 (EL5176 MSOP). ...
Page 2
... Differential Input Resistance IN C Differential Input Capacitance IN DMIR Differential Mode Input Range CMIR+ Common Mode Positive Input Range EL5176 Thermal Information = +25°C) Thermal Resistance (Typical MSOP (Note 1 0. 0.3V Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +135° Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C Storage Temperature Range . . . . . . . . . . . . . . . . . .-65° ...
Page 3
... FBN Inverting feedback input; resistor R 6 OUT- Inverting output Enabled when this pin is floating or the applied voltage ≤ VS+ Positive supply 9 VS- Negative supply 10 OUT+ Non-inverting output 3 EL5176 - = -5V +25° 0V 1kΩ CONDITIONS +, ...
Page 4
... FREQUENCY (Hz) FIGURE 1. FREQUENCY RESPONSE 2.7pF 200Ω 10M FREQUENCY (Hz) FIGURE 3. FREQUENCY RESPONSE EL5176 R F1 0Ω 1 FBP OUT IN+ VS REF VS IN FBN OUT 0Ω ...
Page 5
... FREQUENCY (Hz) FIGURE 7. FREQUENCY RESPONSE - V 0 -10 -20 -30 -40 PSRR- -50 PSRR+ -60 -70 -80 -90 1k 10k 100k 1M FREQUENCY (Hz) FIGURE 9. PSRR vs FREQUENCY 5 EL5176 (Continued 1kΩ 500Ω F 100M 400M 100M REF 10M 100M 1kΩ 2.7pF 1kΩ ...
Page 6
... HD3 (f = 20MHz) -50 HD3 (f = 5MHz) -60 -70 -80 HD2 (f = 5MHz) -90 -100 200 300 400 500 600 700 R (Ω) LD FIGURE 15. HARMONIC DISTORTION EL5176 (Continued 100k 1M 10M FIGURE 12. HARMONIC DISTORTION vs DIFFERENTIAL 800 900 1000 FIGURE 16. HARMONIC DISTORTION vs FREQUENCY ±5V 1kΩ ...
Page 7
... JA 0.3 0.2 0 AMBIENT TEMPERATURE (°C) FIGURE 21. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE 7 EL5176 (Continued) 0.5V/DIV FIGURE 18. LARGE SIGNAL TRANSIENT RESPONSE CH1 CH2 85 100 125 FIGURE 22. PACKAGE POWER DISSIPATION vs AMBIENT 10ns/DIV M = 200ns, CH1 = 500mV/DIV, CH2 = 5V/DIV 200ns/DIV FIGURE 20. DISABLED RESPONSE ...
Page 8
... If the input common mode or differential mode signal is outside the above-specified ranges, it will cause the output signal to become distorted. The output of the EL5176 can swing from -3.8V to +3.9V at 1kΩ differential load at ±5V supply. As the load resistance becomes lower, the output swing is reduced. ...
Page 9
... Again, a small series resistor at the output can help to reduce peaking. Disable/Power-Down The EL5176 can be disabled and its outputs placed in a high impedance state. The turn-off time is about 0.95µs and the turn-on time is about 215ns. When disabled, the amplifier's supply current is reduced to 1.7µA for I typically, thereby effectively eliminating the power consumption ...
Page 10
... As the signal is transmitted through a cable, the high frequency signal will be attenuated. One way to compensate this loss is to boost the high frequency gain at the receiver side TWISTED-PAIR EL5176 100Ω FIGURE 24. TWISTED-PAIR CABLE RECEIVER R ...
Page 11
... PIN 0.5 BSC TOP VIEW H 0.23 +0.07/ -0.08 0. SIDE VIEW 1 5.80 4.40 3.00 0.50 TYPICAL RECOMMENDED LAND PATTERN 11 EL5176 A 0. 1.10 Max B 0.86 ± 0.09 C SEATING PLANE 0.10 ± 0.05 0.10 C NOTES: 1. Dimensions are in millimeters. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Plastic or metal protrusions of 0.15mm max per side are not included ...