LT5557EUF-PBF LINER [Linear Technology], LT5557EUF-PBF Datasheet
LT5557EUF-PBF
Related parts for LT5557EUF-PBF
LT5557EUF-PBF Summary of contents
Page 1
FEATURES ■ 3.3V Operation for Reduced Power Ω ■ 50 Single-Ended RF and LO Ports ■ Wide RF Frequency Range: 400MHz to 3.8GHz* ■ High Input IP3: 25.6dBm at 900MHz 24.7dBm at 1950MHz 23.7dBm at 2.6GHz ■ Conversion Gain: 3.3dB ...
Page 2
... Z = 50Ω, 1600MHz to 2300MHz (No External Matching 50Ω, 1000MHz to 5000MHz (No External Matching) O Differential at 240MHz 1200MHz to 4200MHz 380MHz to 1200MHz U W TOP VIEW ORDER PART NUMBER GND LT5557EUF#PBF + – GND PART MARKING UF PACKAGE 5557 = 125°C, θ ...
Page 3
AC ELECTRICAL CHARACTERISTICS = – 6dBm (–6dBm/tone for 2-tone IIP3 tests, Δf = 1MHz output measured at 240MHz, unless otherwise noted. Test circuit shown in Figure 1. (Notes PARAMETER Conversion Gain Conversion Gain ...
Page 4
LT5557 W U TYPICAL PERFOR A CE CHARACTERISTICS Midband (No external RF/LO matching) 240MHz IF output, P unless otherwise noted. Conversion Gain, IIP3 and Frequency 26 24 IIP3 22 20 LOW-SIDE LO 18 HIGH-SIDE ...
Page 5
W U TYPICAL PERFOR A CE CHARACTERISTICS Midband (No external RF/LO matching) 240MHz IF output, P unless otherwise noted. IF Output Power, IM3 and IM5 vs RF Input Power (2 Input Tones OUT –10 –20 –30 T ...
Page 6
LT5557 W U TYPICAL PERFOR A CE CHARACTERISTICS 900MHz application (with external RF/LO matching), 140MHz IF output, P low-side LO at 0dBm, unless otherwise noted. Conversion Gain, IIP3 and Frequency 28 26 IIP3 24 22 LOW-SIDE LO ...
Page 7
CTIO S NC (Pins 13, 14, 16): Not Connected Internally. These pins should be grounded on the circuit board for the best LO-to-RF and LO-to-IF isolation. RF (Pin 3): Single-Ended Input ...
Page 8
LT5557 TEST CIRCUITS EXTERNAL MATCHING FOR LO BELOW 1GHz LOW-PASS MATCH FOR 450MHz, 900MHz AND 3.6GHz RF *HIGH-PASS MATCH FOR 2.6GHz RF APPLICATION RF MATCH 450MHz High Side 70MHz 6.5mm 900MHz Low Side 140MHz 1.7mm 2.6GHz ...
Page 9
U U APPLICATIO S I FOR ATIO Introduction The LT5557 consists of a high linearity double-balanced mixer, RF buffer amplifier, high speed limiting LO buffer amplifier and bias/enable circuits. The RF and LO inputs are both single ended. The IF ...
Page 10
LT5557 U U APPLICATIO S I FOR ATIO series transmission line/shunt capacitor matching topol- ogy allows the LT5557 to be used for multiple frequency standards without circuit board layout modifications. The series transmission line can also be replaced with a ...
Page 11
U U APPLICATIO S I FOR ATIO The optimum LO drive is –3dBm for LO frequencies above 1.2GHz, although the amplifiers are designed to accom- modate several input power variation without significant mixer performance variation. Below 1.2GHz, ...
Page 12
LT5557 U U APPLICATIO S I FOR ATIO Transformer-Based Bandpass IF Matching The standard evaluation board (shown in Figure 1) uses an L-C bandpass IF matching network, with an 8:1 transformer connected across the IF pins. The L-C network maximizes ...
Page 13
U U APPLICATIO S I FOR ATIO These equations give a good starting point, but it is usually necessary to adjust the component values after building and testing the circuit. The final solution can be achieved with less iteration by ...
Page 14
LT5557 U U APPLICATIO S I FOR ATIO Differential IF Output Matching For fully differential IF architectures, the mixer’s IF out- puts can be matched directly into a SAW filter or IF amplifier, thus eliminating the IF transformer. One ex- ...
Page 15
PACKAGE DESCRIPTIO 4.35 ± 0.05 2.15 ± 0.05 2.90 ± 0.05 (4 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 4.00 ± 0.10 (4 SIDES) PIN 1 TOP MARK (NOTE 6) NOTE: 1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE MO-220 VARIATION ...
Page 16
LT5557 RELATED PARTS PART NUMBER DESCRIPTION Infrastructure LT5511 High Linearity Upconverting Mixer LT5512 1KHz-3GHz High Signal Level Active Mixer LT5514 Ultralow Distortion, IF Amplifier/ADC Driver with Digitally Controlled Gain LT5515 1.5GHz to 2.5GHz Direct Conversion Quadrature Demodulator LT5516 0.8GHz to ...