MAX4865 MAXIM [Maxim Integrated Products], MAX4865 Datasheet - Page 6

no-image

MAX4865

Manufacturer Part Number
MAX4865
Description
Overvoltage Protection Controllers with Reverse Polarity Protection
Manufacturer
MAXIM [Maxim Integrated Products]
Datasheet
The MAX4864L/MAX4865L/MAX4866L/MAX4867 provide
up to +28V overvoltage and negative voltage protection
for low voltage systems. When the input voltage exceeds
the overvoltage trip level, the MAX4864L/MAX4865L/
MAX4866L/MAX4867 turn off a low-cost external n-channel
MOSFET to prevent damage to the protected compo-
nents. The devices also drive an external p-channel
MOSFET to protect against negative voltage inputs. An
internal charge-pump (see the Functional Diagram),
drives the MOSFET GATEN for a simple, robust solution.
On power-up, the device waits for 50ms before driving
GATEN high. The open-drain FLAG output is kept at a
high impedance for an additional 50ms after GATEN goes
high before deasserting. The FLAG output asserts high
immediately to an overvoltage fault.
The MAX4864L/MAX4865L/MAX4866L/MAX4867 have
a fixed +2.85V typical UVLO level, and the MAX4867
has +2.5V UVLO level. When V
the GATEN driver is held low and FLAG is asserted.
The MAX4864L has a +7.4V typical OVLO threshold;
the MAX4865L has +6.35V typical OVLO threshold; the
MAX4866L has a +5.8V typical OVLO threshold; and
the MAX4867 has a +4.65V typical OVLO threshold.
When V
held low and FLAG is asserted.
The open-drain FLAG output is used to signal to the
host system when there is a fault with the input voltage.
On power-up, FLAG is held high for 50ms after GATEN
turns on, before deasserting. FLAG asserts immediately
to overvoltage and undervoltage faults. When the fault
condition is removed, FLAG deasserts 50ms after
GATEN turns on. Connect a pullup resistor from FLAG
to the logic I/O voltage of the host system.
An on-chip charge pump is used to drive GATEN
above IN, allowing the use of a low-cost n-channel
MOSFET. The charge pump operates from the internal
+5.5V regulator.
The actual GATEN output voltage tracks approximately
two times V
level is exceeded, whichever comes first. The
MAX4864L has a +7.4V typical OVLO, therefore GATEN
remains relatively constant at approximately +10.5V for
+5.5V < V
cal OVLO, but this can be as low as +5.5V. The GATEN
Overvoltage Protection Controllers
with Reverse Polarity Protection
6
_______________________________________________________________________________________
IN
IN
is greater than OVLO, the GATEN driver is
IN
< +7.4V. The MAX4866L has a +5.8V typi-
until V
Undervoltage Lockout (UVLO)
Overvoltage Lockout (OVLO)
IN
Detailed Description
exceeds +5.5V, or the OVLO trip
IN
is less than the UVLO,
GATEN Driver
FLAG Output
output voltage is a function of input voltage, as shown
in the Typical Operating Characteristics.
When the input voltage drops below ground, GATEP
goes high turning the external p-channel MOSFET off.
When the input voltage goes above ground, GATEP
pulls low and turns on the p-channel MOSFET. An inter-
nal clamp protects the p-channel MOSFET by insuring
that the GATEP-to-IN voltage does not exceed +16V
when the input (IN) rises to +28V.
The MAX4864L/MAX4865L/MAX4866L/MAX4867 have
an on-board state machine to control device operation.
A flowchart is shown in
V
FLAG is high.
If UVLO < V
50ms internal delay. The internal charge pump is
enabled, and GATEN begins to be driven above V
the internal charge pump. FLAG is held high during
startup until the FLAG blanking period expires, typically
50ms after the GATEN starts going high. At this point,
the device is in its on-state.
At any time if V
high and GATEN is driven to ground.
Figure 5. State Diagram
IN
< UVLO or if V
V
IN
< UVLO
IN
< OVLO, the device enters startup after a
IN
IN
drops below UVLO, FLAG is driven
> OVLO, GATEN is held at 0V and
GATEN DRIVEN HIGH
TIMER STARTS
FLAG = HIGH
OVLO CHECK
GATEN HIGH
FLAG = HIGH
FLAG = LOW
COUNTING
FLAG = HIGH
Figure
GATEN = 0
STANDBY
GATEN = 0
STARTUP
ON
V
t = 50ms
V
t = 50ms
IN
IN
> UVLO
> OVLO
5. On initial power-up, if
Device Operation
GATEP Driver
V
IN
> OVLO
IN
by

Related parts for MAX4865