MAX4113 MAXIM [Maxim Integrated Products], MAX4113 Datasheet
![no-image](/images/no-image-200.jpg)
MAX4113
Available stocks
Related parts for MAX4113
MAX4113 Summary of contents
Page 1
... MAX4118, and quad MAX4119/MAX4120 current feed- back amplifiers combine high-speed performance with low-power operation. The MAX4112/MAX4117/ MAX4119 are optimized for closed-loop gains of 2V/V or greater, while the MAX4113/MAX4118/MAX4120 are optimized for gains of 8V/V or greater. The MAX4112/MAX4117/MAX4119 and the MAX4113/ MAX4118/MAX4120 require only 5mA of supply current per channel, and deliver 0 ...
Page 2
... ±2.0V 0V 100Ω OUT 100Ω 30Ω 0°C to +85° MAX4112/MAX4117 ≤ 0.1V V MAX4113/MAX4119 SS OUT RMS MAX4118/MAX4120 = +25°C.) (Note 1) A MIN TYP MAX UNITS µV/°C 3.5 20 µA 3.5 20 µA 500 kΩ Ω ...
Page 3
... Two-Tone Third-Order Intercept IP3 Crosstalk Note 1: The MAX4112/MAX4113/MAX4117–MAX4120 are designed to operate in a closed-loop configuration in which the IN- pin is driven by the OUT pin through an external feedback network external voltage source is connected to IN-, current into or out of IN- must be limited to ±10mA, to prevent damage to the part. ...
Page 4
... MAX4112/MAX4117/MAX4119 LARGE-SIGNAL GAIN vs. FREQUENCY (A = +2) VCL 600 2Vp-p OUT -6 0 100 1000 FREQUENCY (MHz) MAX4113/MAX4118/MAX4120 SMALL-SIGNAL GAIN vs. FREQUENCY (A = +50) VCL 330 6 100mVp-p OUT -6 0 100 1000 FREQUENCY (MHz) ...
Page 5
... SETTLING TIME vs. GAIN GAIN (V/V) MAX4113/MAX4118/MAX4120 SMALL-SIGNAL PULSE RESPONSE (A = +8) VCL GND IN OUT GND TIME (10ns/div) MAX4113/MAX4118/MAX4120 LARGE-SIGNAL PULSE RESPONSE (A = +20) VCL GND IN OUT GND TIME (10ns/div) MAX4117–MAX4120 CROSSTALK vs. FREQUENCY -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 0.1 1 ...
Page 6
... VCL -60 -70 -80 3rd (A = +8) -90 VCL -100 0 100 FREQUENCY (MHz) 6 _______________________________________________________________________________________ = +25°C, unless otherwise noted.) A INPUT VOLTAGE NOISE vs. FREQUENCY 100 MAX4113/MAX4118/MAX4120 10 MAX4112/MAX4117/MAX4119 100 1k 10k 100k 1M 10M FREQUENCY (Hz) CLOSED-LOOP OUTPUT IMPEDANCE vs. FREQUENCY 1000 100 10 1 0.1 0 100 500 FREQUENCY (MHz) ...
Page 7
... MAX4112/MAX4117/MAX4119 35 30 MAX4113/MAX4118/MAX4120 1000 0 FREQUENCY (MHz) OPEN-LOOP TRANSIMPEDANCE vs. TEMPERATURE 900 MAX4112/MAX4117/MAX4119 800 700 600 100 500 400 MAX4113/MAX4118/MAX4120 300 200 -75 -50 - TEMPERATURE (°C) 100 POSITIVE INPUT BIAS CURRENT vs. TEMPERATURE -2.00 -2.50 -3.00 -3.50 -4.00 -4.50 -5.00 -75 -50 - 100 125 TEMPERATURE (°C) ...
Page 8
Single/Dual/Quad, 400MHz, Low-Power, Current Feedback Amplifiers ____________________________Typical Operating Characteristics (continued +5V -5V 499Ω 100Ω NEGATIVE INPUT BIAS (I CURRENT vs. TEMPERATURE ...
Page 9
... They are designed to drive video loads with low distortion characteristics. The MAX4112/ MAX4117/MAX4119’s differential gain and phase are 0.02% and 0.03°, respectively; the MAX4113/ MAX4118/MAX4120 exhibit gain/phase error specifica- tions of 0.02% and 0.04°, respectively. These charac- teristics, plus a wide 0.1dB gain flatness, make the MAX4112/MAX4113/MAX4117– ...
Page 10
... Layout and Power-Supply Bypassing The MAX4112/MAX4113/MAX4117–MAX4120 have an RF bandwidth and consequently require careful board layout, including the possible use of constant-impedance microstrip or stripline techniques. To realize the full AC performance of these high-speed amplifiers, pay careful attention to power-supply bypassing and board layout. The PC board should ...
Page 11
... For general-purpose use, surface-mount metal-film R resistors seem to have the best overall performance for low cost, low inductance, and low noise The MAX4112/MAX4113/MAX4117–MAX4120 are opti- mized (gain flatness) to drive coaxial transmission lines when the cable is terminated at both ends, as shown ...
Page 12
... Single/Dual/Quad, 400MHz, Low-Power, Current Feedback Amplifiers Driving Capacitive Loads The MAX4112/MAX4113/MAX4117–MAX4120 are opti- mized for AC performance. They are not designed to drive highly capacitive loads. Reactive loads decrease phase margin and can produce excessive ringing and oscillation. Figure 5a shows a circuit that eliminates this problem. The small (usually 5Ω ...