SAB80C515A-5 SIEMENS [Siemens Semiconductor Group], SAB80C515A-5 Datasheet - Page 87
![no-image](/images/no-image-200.jpg)
SAB80C515A-5
Manufacturer Part Number
SAB80C515A-5
Description
8-Bit CMOS Single-Chip Microcontroller Family
Manufacturer
SIEMENS [Siemens Semiconductor Group]
Datasheet
1.SAB80C515A-5.pdf
(108 pages)
- Current page: 87 of 108
- Download datasheet (2Mb)
Requirements for Hardware Power Down Mode
There is no dedicated pin to enable the Hardware Power Down Mode. The control pin PE/SWD
has no control function in this mode. It enables and disables only the use of software controlled
power saving modes.
Software Controlled Power Saving Modes
All of these modes are entered by software. Special function register PCON (power control
register, address is 87
Slow Down Mode
During slow down operation all signal frequencies that are derived from the oscillator clock, are
divided by eight, also the clockout signal and and the watchdog timer count.
The slow down mode is enabled by setting bit SD. The controller actually enters the slow down
mode after a short synchronisation period (max. 2 machine cycles).
The slow down mode is disabled by clearing bit SD.
Idle Mode
During idle mode all peripherals of the SAB 80C515A (except for the watchdog timer) are still
supplied by the oscillator clock. Thus the user has to take care which peripheral should
continue to run and which has to be stopped during Idle.
The procedure to enter the Idle mode is similar to the one entering the power down mode. The
two bits IDLE and IDLS must be set by two consecutive instructions to minimize the chance of
unintentional activating of the idle mode.
There are two ways to terminate the idle mode:
– The idle mode can be terminated by activating any enabled interrupt. This interrupt will be
– The other way to terminate the idle mode, is a hardware reset. Since the oscillator is still
Normally the port pins hold the logical state they had at the time idle mode was activated. If
some pins are programmed to serve their alternate functions they still continue to output during
idle mode if the assigned function is on. The control signals ALE and PSEN hold at logic high
levels (see table 5).
Semiconductor Group
serviced and the instruction to be executed following the RETI instruction will be the one
following the instruction that set the bit IDLS.
running, the hardware reset must be held active only for two machine cycles for a complete
reset.
H
) is used to select one of these modes.
6-35
SAB 80C515A/83C515A-5
Related parts for SAB80C515A-5
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![S80C32-12](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
Intel 80C32 - Siemens SAB-C501, Nearest Equivalent Replacement
Manufacturer:
Siemens Semiconductor Group
![BAT14-033](/images/no-image3.png)
Part Number:
Description:
HiRel Silicon Schottky Diode (HiRel Discrete and Microwave Semiconductor Medium barrier diodes for detector and mixer applications)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
![BXY43-P1](/images/no-image3.png)
Part Number:
Description:
HiRel Silicon PIN Diode (HiRel Discrete and Microwave Semiconductor Current controlled RF resistor for RF attenuators and switches)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
![BXY44-T1](/images/no-image3.png)
Part Number:
Description:
HiRel Silicon PIN Diode (HiRel Discrete and Microwave Semiconductor Current controlled RF resistor for RF attenuators and switches)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
![IRL80](/images/no-image3.png)
Part Number:
Description:
GaAs-Infrarot-Sendediode GaAs Infrared Emitter
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
![IRL81](/images/no-image3.png)
Part Number:
Description:
GaAlAs-Infrarot-Sendediode GaAlAs Infrared Emitter
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
![BSM50GB100D](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
IGBT MODULE
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![BSM181R](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
SIMOPAC Module (Power module Single switch N channel Enhancement mode)
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![BSM254F](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
(BSMxxx) TRANSISTOR
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![BSM111AR](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
SIMOPAC Module (Power module Single switch N channel Enhancement mode)
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![BUZ48](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
main ratings
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![TDA4716C](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![DL440M](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![SDA5255](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet: