MCP4801T-E/P MICROCHIP [Microchip Technology], MCP4801T-E/P Datasheet - Page 25
![no-image](/images/no-image-200.jpg)
MCP4801T-E/P
Manufacturer Part Number
MCP4801T-E/P
Description
8/10/12-Bit Voltage Output Digital-to-Analog Converter with Internal VREF and SPI Interface
Manufacturer
MICROCHIP [Microchip Technology]
Datasheet
1.MCP4801T-EP.pdf
(48 pages)
6.0
The MCP4801/4811/4821 family of devices are general
purpose, single channel voltage output DACs for
various applications where a precision operation with
low-power and internal voltage reference is required.
Applications generally suited for the devices are:
• Set Point or Offset Trimming
• Sensor Calibration
• Precision Selectable Voltage Reference
• Portable Instrumentation (Battery-Powered)
• Calibration of Optical Communication Devices
6.1
The MCP4801/4811/4821 devices utilize a 3-wire
synchronous serial protocol to transfer the DAC’s setup
and input codes from the digital devices. The serial
protocol can be interfaced to SPI or Microwire
peripherals which are common on many microcon-
troller units (MCUs), including Microchip’s PIC
and dsPIC
In addition to the three serial connections (CS, SCK
and SDI), the LDAC signal synchronizes the DAC
output with LDAC pin event. By bringing the LDAC pin
down “low”, the DAC input codes and settings in the
DAC input register are latched into the output register,
and the DAC analog output is updated.
shows an example of the pin connections. Note that the
LDAC pin can be tied low (V
connections from 4 to 3 I/O pins. In this case, the DAC
output can be immediately updated when a valid
16 clock transmission has been received and the CS
pin has been raised.
6.2
The typical application will require a bypass capacitor
to filter out noise in the power supply traces. The noise
can be induced onto the power supply’s traces from
various events such as digital switching or as a result
of changes on the DAC’s output. The bypass capacitor
helps minimize the effect of these noise sources.
Figure 6-1
this example, two bypass capacitors are used in paral-
lel: (a) 0.1 µF (ceramic) and (b)10 µF (tantalum). These
capacitors should be placed as close to the device
power pin (V
The power source supplying these devices should be
as clean as possible. If the application circuit has
separate digital and analog power supplies, V
V
2010 Microchip Technology Inc.
SS
of the device should reside on the analog plane.
TYPICAL APPLICATIONS
Digital Interface
Power Supply Considerations
®
illustrates an appropriate bypass strategy. In
DSCs.
DD
) as possible (within 4 mm).
SS
) to reduce the required
Figure 6-1
®
DD
MCUs
and
6.3
The voltage noise density (in µV/Hz) is illustrated in
Figure
primarily a result of the internal reference voltage.
Its 1/f corner (f
Figure 2-14
mV
effective method to produce a single-pole Low-Pass
Filter (LPF) that will reduce this noise. For instance, a
bypass capacitor sized to produce a 1 kHz LPF would
result in an E
necessary when trying to achieve the low DNL error
performance (at G = 1x) that the MCP4801/4811/4821
devices are capable of. The tested range for stability
is .001 µF through 4.7 µF.
FIGURE 6-1:
Diagram.
6.4
Inductively-coupled AC transients and digital switching
noises can degrade the output signal integrity, and
potentially reduce the device performance. Careful
board layout will minimize these effects and increase
the Signal-to-Noise Ratio (SNR). Bench testing has
shown
low-inductance ground plane, isolated inputs and
isolated outputs with proper decoupling, is critical for
the best performance. Particularly harsh environments
may require shielding of critical signals.
Breadboards and wire-wrapped boards are not
recommended if low noise is desired.
C2 = 0.1 µF
C1 = 10 µF
1 µF
V
MCP4801/4811/4821
OUT
P-P
C1
). A small bypass capacitor on V
2-13. This noise appears at V
V
Output Noise Considerations
Layout Considerations
that
AV
DD
illustrates the voltage noise (in mV
SS
NREF
CORNER
C2
a
SDI
1 µF
V
of about 100 µV
OUT
C1
multi-layer
) is approximately 400 Hz.
Typical Connection
V
AV
DD
SS
C2
SDI
board
RMS
LDAC
DS22244B-page 25
CS
. This would be
SDO
SCK
CS
C1
OUT
0
utilizing
OUT
, and is
V
V
DD
RMS
SS
is an
C2
or
a