MAX6960 MAXIM [Maxim Integrated Products], MAX6960 Datasheet - Page 15

• Manufacturer Part Number: MAX6960
• Description: 4-Wire Serially Interfaced 8 x 8 Matrix Graphic LED Drivers
• Manufacturer: MAXIM [Maxim Integrated Products]

One MAX6960 is designated the master device, and
this is allocated driver address 0. The master’s ADDIN
pin is connected to V+, identifying it as the first device.
This first MAX6960 should be the driver for the top-
left pixels of the display panel. The master’s
ADDOUT pin is connected to the second MAX6960’s
ADDIN pin, and that MAX6960’s ADDOUT pin is con-
nected to the third MAX6960’s ADDIN, and so on up to
256 MAX6960s. The last MAX6960’s ADDOUT pin is left
open circuit. The last MAX6960 should be the driver
for the bottom-right pixels of the display panel. The
ADDOUT is initialized low at the start of a 3-wire inter-
face configuration operation, and goes high (N + 1.5)
ADDCLK periods later, where n is the driver address of
the MAX6960 (0 to 255). See Figures 1 and 2 for con-
nection examples.
The ADDCLK pins for all MAX6960s are all connected
together. ADDCLK data rate is determined by OSC / 4,
nominally 1.048576 MHz. The ADDCLK pin for the mas-
ter MAX6960 (driver address 0) is always an output,
and all the other ADDCLKs are always inputs. ADDCLK
is active for exactly 256 clock cycles when a panel con-
figuration is being performed (on power-up reset, and
after a write to the global panel configuration register).
When the plane counter is configured to automatic
mode (bit 6 of the plane counter register is set) (Table
30), ADDOUT pulses low for a time of 512/OSC (nomi-
nally 122µs) at the start of every automatic plane
change. This signal can be used as an interrupt output
Table 8. Register Address Map
Use of ADDOUT as Plane Change Interrupt
GLOBAL PANEL CONFIGURATION
PLANES/INTENSITY
(PI BIT)
0
0
1
1
REGISTER
3-Wire Interface Clock (ADDCLK)
______________________________________________________________________________________
3-Wire Interface Data Lines
COLOR
(C BIT)
0
1
0
1
(ADDOUT and ADDIN)
8 x 8 Matrix Graphic LED Drivers
2 bits per pixel
2 bits per pixel
PIXEL-LEVEL
1 bit per pixel
1 bit per pixel
INTENSITY
CONTROL
(IRQ)
DISPLAY TYPE
4-Wire Serially Interfaced
Monocolor
Monocolor
RGY
RGY
from the display panel to the host to flag that the previ-
ous display plane is now unused and can be written
with a new image.
The OSC input for all MAX6960s sharing a 3-wire inter-
face bus (but not necessarily a 4-wire interface bus)
should be driven by a common CMOS-level clock rang-
ing between 1MHz and 8.5MHz. It is usually necessary
to use an external clock tree to fan out multiple clock
drives when larger numbers of MAX6960s are used
because of the capacitive loads. For example, each
one of the eight outputs of a standard 74HC541 octal
buffer could drive 8 to 32 MAX6960 OSC inputs,
depending on the layout used.
The recommended setting for OSC is 4.194303MHz.
This frequency sets the slow global plane counter reso-
lution to 1s, and the fast global plane counter resolution
to 1Hz.
The register map (Table 8) contains three local regis-
ters and eight global registers. Global registers are
always written to in all MAX6960s (on the same 4-wire
interface) at the same time, using a 16-bit transmission.
A read from a global register also always results in a
read from driver address 0. The global nature of these
registers ensures that all drivers work together, and
there is no chance of a software miss-send causing, for
example, multiple MAX6960s to try to transmit on the 4-
wire DOUT line at the same time.
The three local registers can be written to on an individ-
ual basis (updates just the MAX6960 indirected by the
global driver indirect address register), or on a global
16 red contiguous
8 red contiguous,
8 green contiguous
16 red contiguous,
16 red contiguous
16 red
(2 noncontiguous groups of 8),
16 green
(2 noncontiguous groups of 8)
ADDRESSES PER PLANE
Global and Local Register
DISPLAY MAPPING
Multiplex Clock
Addressing
AVAILABLE
DISPLAY
PLANES
4
4
2
2
15