MAX5355 MAXIM [Maxim Integrated Products], MAX5355 Datasheet - Page 9

• Manufacturer Part Number: MAX5355
• Description: 10-Bit Voltage-Output DACs in 8-Pin ?MAX
• Manufacturer: MAXIM [Maxim Integrated Products]

The MAX5354/MAX5355 contain a voltage-output digi-
tal-to-analog converter (DAC) that is easily addressed
using a simple 3-wire serial interface. Each IC includes
a 16-bit shift register, and has a double-buffered input
composed of an input register and a DAC register (see
Functional Diagram ). In addition to the voltage output,
the amplifier’s negative input is available to the user.
The DAC is an inverted R-2R ladder network that con-
verts a digital input (10 data bits plus three sub-bits)
into an equivalent analog output voltage in proportion
to the applied reference voltage. Figure 1 shows a sim-
plified circuit diagram of the DAC.
The reference input accepts positive DC and AC sig-
nals. The voltage at the reference input sets the full-
scale output voltage for the DAC. The reference input
voltage range is 0V to (V
(V
age source, as expressed in the following equation:
where NB is the numeric value of the DAC’s binary
input code (0 to 1023), V
and Gain is the externally set voltage gain.
The impedance at the reference input is code depen-
dent, ranging from a low value of 18kΩ when the DAC
has an input code of 1550 hex, to a high value exceed-
ing several giga ohms (leakage currents) with an input
code of 0000 hex. Because the input impedance at the
reference pin is code dependent, load regulation of the
reference source is important.
_____________________Pin Description
_______________Detailed Description
OUT
PIN
1
2
3
4
5
6
7
8
) is represented by a digitally programmable volt-
V
OUT
NAME
SCLK
GND
OUT
DIN
REF
V
CS
FB
DD
= (V
_______________________________________________________________________________________
REF
DAC Output Voltage
Chip-Select Input. Active low.
Serial-Data Input
Serial-Clock Input
DAC Output Amplifier Feedback
Reference Voltage Input
Ground
Positive Power Supply
x NB / 1024) x Gain
DD
REF
- 1.4V). The output voltage
is the reference voltage,
Reference Inputs
FUNCTION
10-Bit Voltage-Output DACs
In shutdown mode, the MAX5354/MAX5355’s REF input
enters a high-impedance state with a typical input leak-
age current of 0.001µA.
The reference input capacitance is also code depen-
dent and typically ranges from 15pF (with an input
code of all 0s) to 50pF (at full scale).
The MAX873 +2.5V reference is recommended for use
with the MAX5354.
The MAX5354/MAX5355’s DAC output is internally
buffered by a precision amplifier with a typical slew rate
of 0.6V/µs. Access to the output amplifier’s inverting
input provides the user greater flexibility in output gain
setting/signal conditioning (see the Applications
Information section).
With a full-scale transition at the MAX5354/MAX5355
output, the typical settling time to ±1/2LSB is 10µs
when loaded with 5kΩ in parallel with 100pF (loads less
than 2kΩ degrade performance).
The amplifier’s output dynamic responses and settling
performances are shown in the Typical Operating
Characteristics .
The MAX5354/MAX5355 feature a software-program-
mable shutdown that reduces supply current to a typical
value of 4µA. Writing 111X XXXX XXXX XXXX as the input-
control word puts the device in shutdown mode (Table 1).
Figure 1. Simplified DAC Circuit Diagram
AGND
REF
SHOWN FOR ALL 1s ON DAC
2R
2R
R
in 8-Pin µMAX
2R
R
2R
R
Output Amplifier
Shutdown Mode
2R
MSB
FB
OUT
9