APA18T04_05 ASTEC [Astec America, Inc], APA18T04_05 Datasheet
APA18T04_05
Related parts for APA18T04_05
APA18T04_05 Summary of contents
Page 1
APA18T04 – 3.0-5.5Vin, 18A, Non-isolated DC – DC SIP Converter The single output APA18T04 is a non-isolated, 60W, SIP footprint Point-of-Load (POL) DC/DC converter. The new APA18T04 series can deliver an adjustable output voltage range from 0.75V – 3.3V at ...
Page 2
THIS TECHNICAL REFEENCE NOTES COVERS THE SPECIFICATIONS FOR A SINGLE OUTPUT, OPEN-FRAME, NON-ISOLATED DC-DC CONVERTER WITH ADJUSTABLE OUTPUT FROM 0.75V TO 3.3V HAVING 59.4W MAXIMUM OUTPUT POWER WHEN OPERATED FROM A NOMINAL 5 VDC SOURCE. THE MECHANICAL OUTLINE IS 50.8MM ...
Page 3
Electrical Specifications The product shall comply with the requirements of this specification for all valid conditions of line input voltage, load current, temperature and other environmental conditions, unless otherwise specified in this document. Description External Input Fuse External Input Capacitance ...
Page 4
ABSOLUTE MAXIMUM RATINGS Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational ...
Page 5
OUTPUT SPECIFICATIONS Parameter Output Voltage Set point IN, MIN IN,MAX max Output Regulation Line IN, min Load ...
Page 6
OUTPUT SPECIFICATIONS Parameter 6 Dynamic Response (C O Tantalum + 1uF ceramic) Load Change of 50% step anywhere between 10% to 100% of rated load Peak Deviation Settling Time to V <5% O, Nom Peak deviation 6 Dynamic Response (C ...
Page 7
APPENDIX A1: CONVERTER ORIENTATION WRT TO AIRFLOW Model: APA18T04 Series Date: Aug 2005 Technical Reference Note APA18T04 Series Figure 1. Airflow Orientation and Thermal Test Setup ...
Page 8
APPENDIX A2: INPUT REFLECTED RIPPLE TEST SETUP L1 Vin+ Cin C1 1000uF 150uF Vin- Note: Measure input reflected-ripple current with a simulated source inductance (Ltest) of 1uH. Capacitor Cs offsets possible battery impedance. Measure current as shown above. Input capacitors: ...
Page 9
APPENDIX A3: OUTPUT RIPPLE TEST SETUP Figure 3. Peak-to-Peak Output Noise Measurement Test Setup. Note: (1) Use @50V X7R ceramic capacitor and 10V tantalum capacitor. (2) Use 2 x 150uF/6.3V special polymer(Sanyo 6TPE150M ...
Page 10
APPENDIX A4: TYPICAL APPLICATION CIRCUIT F1 Vin+ FUSE Cin1 Vsource Vin- F1: Fuse: Use external fuse (Fast-acting type 25A) for each unit. Input capacitors: Cin1: 150uF/ special polymer (Sanyo 6TPE150M,or Panasonic EEFUE0J151R) Cin2: 47uF/10V x2 Ceramic Output capacitors: ...
Page 11
APPENDIX A5: TIMING DIAGRAM Model: APA18T04 Series Date: Aug 2005 Technical Reference Note APA18T04 Series Figure 6. Timing diagram ...
Page 12
APPENDIX A6: OUTPUT TRIM REQUIREMENT Output voltage adjustment is accomplished by connecting an external resistor between the Trim Pin and Ground Pin terminals. Resistance and Output voltage relationship is established by Equation 1. If Trim pin is left open – ...
Page 13
APPENDIX B: THERMAL DERATING CURVES NOTE: These curves are limited by OTP Model: APA18T04 Series Date: ...
Page 14
Model: APA18T04 Series Date: Aug 2005 Technical Reference Note APA18T04 Series 300 LFM 200 ...
Page 15
Model: APA18T04 Series Date: Aug 2005 Technical Reference Note APA18T04 Series 300 LFM 200 LFM ...
Page 16
APPENDIX C: MODULE PIN ASSIGNMENT PIN # +V IN Enable GND Sense Note: The pinout assignment of APA18T04-9 and APA18T04-9H are the same. APPENDIX D: MECHANICAL OUTLINE/DRAWING (for reference only) Figure 14. APA18 Mechanical Outline/ Drawing for Vertical type Model: ...
Page 17
Figure 15. APA18 Mechanical Outline/ Drawing for Horizontal type Pin Number P10 Model: APA18T04 Series Date: Aug 2005 Technical Reference Note APA18T04 Series Pin Connection Vo Output Voltage ...