MBM29LV160B FUJITSU [Fujitsu Component Limited.], MBM29LV160B Datasheet - Page 3
![no-image](/images/no-image-200.jpg)
MBM29LV160B
Manufacturer Part Number
MBM29LV160B
Description
Manufacturer
FUJITSU [Fujitsu Component Limited.]
Datasheet
1.MBM29LV160B.pdf
(60 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MBM29LV160B-90PFTN
Manufacturer:
FUJI
Quantity:
2 241
Part Number:
MBM29LV160B-90PFTN
Manufacturer:
FUJITSU/富士通
Quantity:
20 000
Company:
Part Number:
MBM29LV160B-90PFTN-SFK
Manufacturer:
FUJITSU
Quantity:
50
Part Number:
MBM29LV160BE-70PFTI
Manufacturer:
FUJI/富士电机
Quantity:
20 000
Company:
Part Number:
MBM29LV160BE-70PFTN
Manufacturer:
FUJI
Quantity:
976
Part Number:
MBM29LV160BE-70TN
Manufacturer:
FUJI/富士电机
Quantity:
20 000
Part Number:
MBM29LV160BE-70TN/PFTN
Manufacturer:
FUJITSU/富士通
Quantity:
20 000
Company:
Part Number:
MBM29LV160BE-90PFTN
Manufacturer:
FUJITSU
Quantity:
135
Part Number:
MBM29LV160BE-90PFTN
Manufacturer:
FUJITSU
Quantity:
20 000
Company:
Part Number:
MBM29LV160BE90TN-K
Manufacturer:
FUJITSU
Quantity:
68
MBM29LV160T
/MBM29LV160B
-80/-90/-12
-80/-90/-12
GENERAL DESCRIPTION
The MBM29LV160T/B is a 16M-bit, 3.0 V-only Flash memory organized as 2M bytes of 8 bits each or 1M words
of 16 bits each. The MBM29LV160T/B is offered in a 48-pin TSOP (I), 46-pin SON, 48-pin CSOP and 48-ball
FBGA packages. The device is designed to be programmed in-system with the standard system 3.0 V V
supply.
CC
12.0 V V
and 5.0 V V
are not required for write or erase operations. The device can also be reprogrammed
PP
CC
in standard EPROM programmers.
The standard MBM29LV160T/B offers access times of 80 ns and 120 ns, allowing operation of high-speed
microprocessors without wait states. To eliminate bus contention the device has separate chip enable (CE), write
enable (WE), and output enable (OE) controls.
2
The MBM29LV160T/B is pin and command set compatible with JEDEC standard E
PROMs. Commands are
written to the command register using standard microprocessor write timings. Register contents serve as input
to an internal state-machine which controls the erase and programming circuitry. Write cycles also internally
latch addresses and data needed for the programming and erase operations. Reading data out of the device is
similar to reading from 5.0 V and 12.0 V Flash or EPROM devices.
The MBM29LV160T/B is programmed by executing the program command sequence. This will invoke the
Embedded Program Algorithm which is an internal algorithm that automatically times the program pulse widths
and verifies proper cell margins. Typically, each sector can be programmed and verified in about 0.5 seconds.
Erase is accomplished by executing the erase command sequence. This will invoke the Embedded Erase
Algorithm which is an internal algorithm that automatically preprograms the array if it is not already programmed
before executing the erase operation. During erase, the device automatically times the erase pulse widths and
verifies proper cell margins.
Any individual sector is typically erased and verified in 1.0 second. (If already preprogrammed.)
The device also features a sector erase architecture. The sector mode allows each sector to be erased and
reprogrammed without affecting other sectors. The MBM29LV160T/B is erased when shipped from the factory.
The device features single 3.0 V power supply operation for both read and write functions. Internally generated
and regulated voltages are provided for the program and erase operations. A low V
detector automatically
CC
inhibits write operations on the loss of power. The end of program or erase is detected by Data Polling of DQ
,
7
by the Toggle Bit feature on DQ
, or the RY/BY output pin. Once the end of a program or erase cycle has been
6
comleted, the device internally resets to the read mode.
The MBM29LV160T/B also has a hardware RESET pin. When this pin is driven low, execution of any Embedded
Program Algorithm or Embedded Erase Algorithm is terminated. The internal state machine is then reset to the
read mode. The RESET pin may be tied to the system reset circuitry. Therefore, if a system reset occurs during
the Embedded Program Algorithm or Embedded Erase Algorithm, the device is automatically reset to the read
mode and will have erroneous data stored in the address locations being programmed or erased. These locations
need re-writing after the Reset. Resetting the device enables the system’s microprocessor to read the boot-up
firmware from the Flash memory.
Fujitsu’s Flash technology combines years of Flash memory manufacturing experience to produce the highest
levels of quality, reliability, and cost effectiveness. The MBM29LV160T/B memory electrically erases all bits within
a sector simultaneously via Fowler-Nordhiem tunneling. The bytes/words are programmed one byte/word at a
time using the EPROM programming mechanism of hot electron injection.
3