SG29055AP MICROSEMI [Microsemi Corporation], SG29055AP Datasheet - Page 4
![no-image](/images/no-image-200.jpg)
SG29055AP
Manufacturer Part Number
SG29055AP
Description
LOW DROPOUT DUAL REGULATOR
Manufacturer
MICROSEMI [Microsemi Corporation]
Datasheet
1.SG29055AP.pdf
(4 pages)
12/90 Rev 1.1 2/94
Copyright
APPLICATION HINTS
EXTERNAL CAPACITORS
To stabilize the outputs and prevent oscillation (perhaps by many
volts) external capacitors are required. The minimum recom-
mended value for the output capacitors is 10µF, although the
actual size and type will likely vary according to the particular
application, e.g., operating temperature range and load. Another
consideration is the effective series resistance (ESR) of the
capacitor. Capacitor ESR will vary by manufacturer. Conse-
quently, some evaluation may be required to determine the
minimum value of the output capacitors. Generally worst case
occurs at the maximum load and minimum ambient temperature.
The size of the output capacitor can be increased to any value
above the minimum. One possible advantage of this would be to
maintain the output voltage during brief periods of negative input
transients
The output capacitors chosen should be rated for the full range
of ambient temperature over which the circuit will be exposed and
expected to operate. For example, many aluminum type electro-
lytic capacitors will freeze at -30°C. The effective capacitance is
reduced to zero in such a situation. Capacitors rated for -40°C
operation must be used in order to maintain regulator stability at
that temperature. Tantalum capacitors satisfy this requirement.
STANDBY OUTPUT
The SG29055/55A differs from most fixed voltage regulators in
that it is equipped with two regulator outputs instead of one. The
additional output is intended for use in systems requiring standby
memory circuits. While the high current regulator output can be
controlled with the ON/OFF pin described below, the standby
remains on under all conditions as long as sufficient input voltage
is applied to the IC. Thus, memory and other circuits powered by
this output remain unaffected by positive line transients, thermal
shutdown, etc.
The standby regulator circuit is designed so that the quiescent
current to the IC is very low (<1.5mA) when the other regulator
output is off.
If the standby output is not required it can be disabled. This is
accomplished by connecting a resistor from the standby output to
the supply voltage, thereby also eliminating the requirement for
a more expensive output capacitor to prevent unwanted oscilla-
tions. The resistor value depends upon the minimum input
voltage expected for a given system.
Since the standby output is shunted with an internal 5.6V zener,
CONNECTION DIAGRAM & ORDERING INFORMATION
Note: 1. All parts are viewed from the top.
5-PIN TO-220 PLASTIC
P - PACKAGE
Package
1994
Part No.
SG29055P
SG29055AP
Temperature Range
-40 C to 85 C
-40 C to 85 C
Ambient
4
(See Note Below)
the current through the external resistor should be sufficient to
bias internal resistors up to this point. Approximately 60 A will
suffice, resulting in a 10k external resistor for most applications
(Figure 1).
HIGH CURRENT OUTPUT
The high current regulated output features fault protection
against overvoltage as well as a thermal shutdown feature. If the
input voltage rises above 33V (load dump), the high current
output shuts down automatically. The internal circuitry is thus
protected and the IC is able to survive higher voltage transients
than might otherwise be expected. The thermal shutdown of the
high current output effectively guards against overheating of the
die since this section of the IC is the principle source of power
dissipation on the chip.
ON/OFF SWITCH
The ON/OFF pin is a high impedance low current switch that
controls the main output voltage (pin 2). This is directly compat-
ible with all 5 volt logic families. For use with open collector logic
outputs, a 50K resistor from this pin to a 5V supply, such as Pin
5, is required.
The SG29055/55A also has an internal pulldown resistor on pin
2 to ground. This resistor, approximately 90K in value, ensures
the high current switched output remains off unless actively
pulled high.
FIGURE 1. Disabling Standby Output to Eliminate C3
Connection Diagram
GND
SG29055/55A
11861 Western Avenue
V
IN
R
10K
C3
D
L
INFINITY Microelectronics Inc.
(714) 898-8121
5 STANBY OUTPUT
4 ON/OFF SWITCH
3 GROUND
2 OUTPUT VOLTAGE (V
1 INPUT VOLTAGE (V
STANDBY
OUTPUT
SG29055/55A
Garden Grove, CA 92841
FAX: (714) 893-2570
IN
)
OUT
)