SL6609AKGNPDE MITEL [Mitel Networks Corporation], SL6609AKGNPDE Datasheet - Page 8

• Manufacturer Part Number: SL6609AKGNPDE
• Description: Direct Conversion FSK Data Receiver
• Manufacturer: MITEL [Mitel Networks Corporation]

COMPONENTS LIST FOR APPLICATION BOARD
(LO circuit is 50
SL6609A
Notes
1.
2.
3.
4.
8
Resistors
R1
R2
R3
R4
R5
R6
R7
R8
R9
R10
R11
R12
R13
R14
R15
R16
R17
R18
R22
Capacitors
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
The values of R13 is determined by the set-up proce-
dure. See Application Note.
The value of "C9" is determined by the output data rate.
Use 2nF for 512bps, 1nF for 1200bps and 470pF for
2400bps.
R12 & Q4 form a dummy load for the regulator.
Permitted load currents for the regulator are 250 A to
5mA. The 1V regulator (output Pin 23) can be switched
off by connecting Pin 23 directly to VCC2. Q1, Q4, R12
and C12 must then be omitted
L2 is used in the Audio AGC circuit (see Fig.6). For the
characteristics of the Audio AGC current source see
figure 7. If the Audio AGC is not required then the
current source (Pin 28) may be disabled by connecting
open circuit
open circuit
100
100k
100
100
100
open circuit
220k
1M
100k
300
3k9
4k7
4k7
33k
open circuit
0R
open circuit
1n
3.3pF
1n
1n
3.9pF
2u2
1n
100n
1n
2u2
100n
1n
1n
(2)
network as in Fig.5 - crystal oscillator not specified)
(4)
(1)
(3)
(2)
(4)
At 470MHz, 25kHz Channel Spacing.
5.
6.
7.
C14
C15
C16
C17
C18
C19
C20
C21
C22
C23
C24
C25
C26
C27
C28
C29
C30
C31
C34
VC1
Inductors
L1
L2
T1
Active Components
Q1
Q2
Q3
Q4
Q5
D1
Pin 9 (TCADJ) to VR (Pin 6) and by connecting Pin 28
(IAGCOUT) to Vcc1, (R18). The voltage at Pin 8 may
still be used as an RSSI. R9, C8, C14, C19, R17 and
D1 may then be omitted.
L1and C26 form the low noise matching network for the
RF amplifier. The values given are for the RF amplifier
specified in the Applications Circuit with no Audio AGC
connected. i.e. R17 and D1 omitted.
Suggested diode for use with the Audio AGC circuit
(D1 is not included on the general demonstration
circuit).
The value of R11 is dependent on the data output load.
R11 should allow sufficient current to drive the data
output load.
1n
1n
1n
1n
1n
not used
1n
1n
not used
not used
1n
1n
open circuit
not used
not used
100p
2u2
2u2
1p5
1-3pF
47nH
not used
16nH 2 Turn 1:1 (Coilcraft) Q4123-A
Zetex FMMT589
Philips BFT25A
Not Used
Philips BFT25A
Philips BFT25A
Panasonic MA862
(5)
(3)
(3)
(6)