LTC4160-1 LINER [Linear Technology], LTC4160-1 Datasheet
![no-image](/images/no-image-200.jpg)
LTC4160-1
Related parts for LTC4160-1
LTC4160-1 Summary of contents
Page 1
... USB On-The-Go And Overvoltage Protection DESCRIPTION The LTC ® 4160/LTC4160-1 are high effi ciency power man- agement and Li-Ion/Polymer battery charger ICs. They each include a bidirectional switching PowerPath™ controller with automatic load prioritization, a battery charger, and an ideal diode. The LTC4160/LTC4160-1’s bidirectional switching regulator ...
Page 2
... LTC4160/LTC4160-1 ABSOLUTE MAXIMUM RATINGS (Notes (Transient) t < 1ms, Duty Cycle < –0. BUS V (Static), BAT, V NTC, ENOTG, ID, BUS OUT, ENCHARGER, VBUSGD, FAULT, CHRG......... –0. ........ –0.3V to Max(V LIM0 ILIM1 BUS I ...................................................................10mA OVSENS I ....................................................................3mA CLPROG .............................................50mA CHRG ...
Page 3
... OUT VBUS PMOS Switch Off With 6.2k Series Resistor V < V OVSENS OVCUTOFF V > V OVSENS OVCUTOFF OVGATE C = 1nF LOAD LTC4160 l LTC4160 845Ω, 10x Mode R ≤ 2.49k PROG CLPROG 10x Mode PROG V > Suspend Mode, BUS UVLO I = 0μA VOUT ...
Page 4
... LTC4160/LTC4160-1 ELECTRICAL CHARACTERISTICS temperature range, otherwise specifi cations are at T otherwise noted. SYMBOL PARAMETER V PROG Pin Servo Voltage PROG V PROG Pin Servo Voltage in Trickle Charge BAT < V PROG_TRKL V C/10 Threshold Voltage at PROG C/10 h Ratio PROG Pin Current PROG BAT I Trickle Charge Current ...
Page 5
... BUS 20 1x MODE PROG 0 4.2 2.7 3.0 3.3 3.6 3.9 BATTERY VOLTAGE (V) LTC4160/LTC4160-1 /R • 1). CLPROG CLPROG CLPROG by (V OUT BUS is expressed as a fraction of the measured full charge current T = 25°C, unless otherwise noted. A Battery and V Currents vs BUS Load Current 750 = 5V V CURRENT ...
Page 6
... LTC4160/LTC4160-1 TYPICAL PERFORMANCE CHARACTERISTICS Ideal Diode V-I Characteristics 1.0 INTERNAL IDEAL DIODE WITH SUPPLEMENTAL EXTERNAL VISHAY 0.8 Si2333 PMOS 0.6 INTERNAL IDEAL DIODE ONLY 0.4 0 BUS 0 0 0.04 0.08 0.12 0.16 FORWARD VOLTAGE (V) 41601 G07 Battery Charge Current vs V OUT Voltage 600 R = 3.01k CLPROG PROG 500 5x MODE 400 ...
Page 7
... TEMPERATURE (°C) V Quiescent Current in BUS Suspend vs Temperature BUS –40 – TEMPERATURE (°C) LTC4160/LTC4160 25°C, unless otherwise noted Current vs Load Current in BUS Suspend 0 BUS BAT = 3. 3.01k CLPROG 0.4 0.3 0.2 0.1 0 0.5 0 0.1 0.2 0.3 LOAD CURRENT (mA) 41601 G17 ...
Page 8
... LTC4160/LTC4160-1 TYPICAL PERFORMANCE CHARACTERISTICS OTG Boost Quiescent Current vs Battery Voltage 3 BAT OUT 2.5 2.0 1.5 1.0 0.5 2.7 3.9 3.0 3.3 3.6 BATTERY VOLTAGE (V) 41601 G25 OTG Boost Effi ciency vs Battery Voltage 100 V = BAT OUT 95 500mA LOAD 100mA LOAD 75 70 2.7 3.9 3.0 3.3 3.6 BATTERY VOLTAGE (V) 41601 G28 OTG Boost Transient Response V BUS 50mV/DIV ...
Page 9
... TO 10V STEP 5V/DIV 500μs/DIV OVSENS Quiescent Current vs Temperature OVSENS –40 – TEMPERATURE (°C) LTC4160/LTC4160 25°C, unless otherwise noted. A Oscillator Frequency vs Temperature 2.30 2.25 2.20 2.15 2.10 41601 G35 2.05 –40 – TEMPERATURE (°C) Rising OVP Threshold vs Temperature 6.47 6.46 6 ...
Page 10
... BUS Voltage of the Battery Charger. The majority of the portable product should be powered from V LTC4160-1 will partition the available power between the external load on V Priority is given to the external load and any extra power is used to charge the battery. An ideal diode from BAT to ...
Page 11
... NTC to ground. To disable NTC operation, connect NTC to GND and leave NTCBIAS open. Exposed Pad (Pin 21): Ground. The Exposed Pad should be connected to a continuous ground plane on the second layer of the printed circuit board by several vias directly under the LTC4160/LTC4160-1. LTC4160/LTC4160 may be used for light loads OUT . ...
Page 12
... LTC4160/LTC4160-1 BLOCK DIAGRAM 12 41601f ...
Page 13
... Bat-Track. Because power is conserved, the LTC4160/LTC4160-1 allow the load current on V exceed the current drawn by the USB port, making maxi- mum use of the allowable USB power for battery charging. ...
Page 14
... OVGATE 2 OVERVOLTAGE PROTECTION OVSENS Figure 1. Power Path Block Diagram – Power Available from USB/Wall Adapter 14 where I VBUSQ LTC4160-1, V current limit, R and LIM0 resistor and h rent at V BUS Refer to the Electrical Characteristics table for values CLPROG tolerances, the USB specifi cation for the average input ...
Page 15
... V be suffi cient negative slope on the inductor current when the PMOS switch balance the rise in the inductor OUT Burst Mode is a registered trademark of Linear Technology Corporation. LTC4160/LTC4160-1 and is capable of delivering at least 500mA. and prevents OUT rises above 2.8V. To prevent ...
Page 16
... ENOTG grounded, must be cycled high and then low. Ideal Diode(s) from BAT to V OUT The LTC4160/LTC4160-1 each have an internal ideal diode as well as a controller for an external ideal diode. Both the internal and the external ideal diodes are always on and will respond quickly whenever V ...
Page 17
... BAT. Capable of driving a 1nF load, the IDGATE pin can control an external P-channel MOSFET having an on-resistance of 30mΩ or lower. Suspend LDO If the LTC4160/LTC4160-1 is confi gured for USB suspend mode, the bidirectional switching regulator is disabled and the suspend LDO provides power to the V suming there is power available at V prevent the battery from running down when the portable product has access to a suspended USB port ...
Page 18
... BUS charge current has dropped to one tenth of the programmed is removed and then value, the CHRG pin goes high. The CHRG pin does not respond to the C/10 threshold if the LTC4160/LTC4160 BUS charge indications due to insuffi cient power available to the battery charger. ...
Page 19
... PAUSE EVENT TIMER RUN EVENT TIMER TIMER > 4 HOURS YES STOP CHARGING YES BAT RISING CHRG Hi-Z THROUGH V RECHRG NO BAT FALLING YES THROUGH BAT < V RECHRG V RECHRG YES NO LTC4160/LTC4160-1 INHIBIT CHARGING PAUSE EVENT TIMER < C/10 BAT YES CHRG Hi-Z NO 41601 FLOW 41601f 19 ...
Page 20
... The benefi the LTC4160/ LTC4160-1 thermal regulation loop is that charge current can be set according to actual conditions rather than worst-case conditions for a given application with the assurance that the charger will automatically reduce the has occurred ...
Page 21
... Because the V voltage range and V BUS of the PowerPath switching regulator are both fairly nar- row, the LTC4160/LTC4160-1 were designed for a specifi c inductance value of 3.3μH. Some inductors which may be suitable for this application are listed in Table 3. Table 3. Recommended PowerPath Inductors for the ...
Page 22
... SOT-23 Battery Charger Over Programming SOT-23 The USB high power specifi cation allows for up to 2.5W SOT- drawn from the USB port. The LTC4160/LTC4160-1’s WDFN6 bidirectional switching regulator in step-down mode con- verts the voltage while limiting power to less than the amount pro- OUT grammed at CLPROG ...
Page 23
... Battery Charger Stability Considerations The LTC4160/LTC4160-1’s battery charger contains both a constant-voltage and a constant-current control loop. The constant-voltage loop is stable without any compensation when a battery is connected with low impedance leads. ...
Page 24
... R – r • NOM HOT 3 266 0 4368 . – • 100 k 104 714 . LTC4160/LTC4160-1 3 NTC BLOCK 0.765 • NTCBIAS – TOO_COLD + 4 – TOO_HOT 0.349 • NTCBIAS + + NTC_ENABLE – 0.1V Figure 7. Standard NTC Confi guration is 1.436 k 41601 F07 41601f ...
Page 25
... V observe voltage overshoot on V BUS LTC4160/LTC4160 lab supply if the overvoltage protection circuit is not used. This overshoot is caused by the inductance of the long leads from the supply to V Twisting the wires together from the supply to V ...
Page 26
... N-channel MOSFET switch. Furthermore, due to its high frequency switching circuitry imperative that the input capacitor, inductor, and output capacitor be as close to the LTC4160/LTC4160-1 as pos- sible and that there be an unbroken ground plane under the LTC4160/LTC4160-1 and all of its external high frequency components ...
Page 27
... FOR STANDARD HOST – Figure 10. LTC4160/LTC4160-1 as the B Device When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the LTC4160/LTC4160-1: 1. The Exposed Pad of the package (Pin 21) should connect directly to a large ground plane to minimize thermal and electrical impedance ...
Page 28
... ID 19 NTCBIAS NTC CLPROG PROG 0.1μF 3.01k 1k 0402 USB 13 V BUS C1 1 10μF OVGATE 0805 2 OVSENS 15 I LIM0 16 I LIM1 LTC4160/LTC4160-1 6 ENOTG 7 ENCHARGER NTCBIAS NTC CLPROG PROG 3.01k 1k 0.1μF 0402 L1 3.3μH 14 SYSTEM SW LOAD 12 V OUT C3 10 IDGATE 22μ ...
Page 29
... OVSENS 15 I GND LIM0 16 LTC4160/LTC4160-1 I LIM1 6 ENOTG 7 ENCHARGER VBUSGD 5 CHRG ID 19 FAULT NTCBIAS LDO3V3 NTC CLPROG PROG 0.1μF 3.01k 1k 0402 LTC4160/LTC4160-1 L1 3.3μ 22μ 0805 + Li-Ion RTC 1μF 41601 TA04 SYSTEM LOAD 41601f 29 ...
Page 30
... TO μC C1, C3: TAYIO YUDEN JMK212BJ226MG L1: COILCRAFT LPS4018-332LM M1: SILICONIX Si2333DS M2: FAIRCHILD FDN372S R1: 1/10 WATT RESISTOR R2: VISHAY CURVE 1 30 USB 13 V BUS C1 22μF 0805 1 OVGATE 2 OVSENS 15 I LIM0 16 LTC4160/LTC4160-1 I LIM1 6 ENOTG 7 ENCHARGER NTCBIAS 100k NTC CLPROG PROG 3.01k 1k T 0.1μF ...
Page 31
... Plastic UTQFN (3mm × 4mm) (Reference LTC DWG # 05-08-1752 Rev Ø) 0.70 ±0.05 2.65 ± 0.05 PACKAGE OUTLINE 2.50 REF 3.10 ± 0.05 4.50 ± 0.05 0.55 ± 0. 0.05 TYP 3.00 ± 0.10 2.50 REF 0.127 REF 0.00 – 0.05 LTC4160/LTC4160-1 PIN 1 NOTCH R = 0.20 OR 0.25 45° CHAMFER 1.50 REF 19 20 0.40 ± 0. 2.65 ± 0.10 1.65 ± 0.10 (PDC20) UTQFN 0407 REV Ø 0.25 ± 0. 0.115 ...
Page 32
... Linear Technology Corporation 32 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 ● BUS V OUT IDGATE 1 OVGATE BAT 2 OVSENS 15 I LIM0 GND 16 LTC4160/LTC4160-1 I LIM1 ENCHARGER VBUSGD 6 CHRG ENOTG 19 FAULT NTCBIAS LDO3V3 NTC CLPROG PROG 0.1μF 3.01k ...