LTC4069EDC-4.4-PBF LINER [Linear Technology], LTC4069EDC-4.4-PBF Datasheet
![no-image](/images/no-image-200.jpg)
LTC4069EDC-4.4-PBF
Related parts for LTC4069EDC-4.4-PBF
LTC4069EDC-4.4-PBF Summary of contents
Page 1
FEATURES n Complete Linear Charger in 2mm × 2mm DFN Package n C/10 Charge Current Detection Output n Timer Charge Termination n Charge Current Programmable Up to 750mA with 5% Accuracy n No External MOSFET, Sense Resistor or Blocking Diode ...
Page 2
... LEAD FREE FINISH TAPE AND REEL LTC4069EDC-4.4#PBF LTC4069EDC-4.4#TRPBF Consult LTC Marketing for parts specifi ed with wider operating temperature ranges. Consult LTC Marketing for information on non-standard lead based fi nish parts. For more information on lead free part marking, go to: For more information on tape and reel specifi ...
Page 3
ELECTRICAL CHARACTERISTICS l The denotes specifi cations which apply over the full operating temperature range, otherwise specifi cations are 5V 3.8V unless otherwise specifi ed. (Note 2) CC BAT NTC SYMBOL PARAMETER ...
Page 4
LTC4069-4.4 TYPICAL PERFORMANCE CHARACTERISTICS Battery Regulation (Float) Voltage vs Charge Current 4. 25° PROG 4.42 4.40 4.38 4.36 0 100 200 400 300 I (mA) BAT 4069 G01 Charge Current ...
Page 5
TYPICAL PERFORMANCE CHARACTERISTICS Undervoltage Lockout Threshold Voltage vs Temperature 4.00 3.75 RISE 3.50 3.25 FALL 3.00 2.75 2.50 – –25 TEMPERATURE (°C) 4069 G16 CHRG Pin Output Low Voltage vs Temperature 140 ...
Page 6
LTC4069-4.4 PIN FUNCTIONS GND (Pin 1): Ground. CHRG (Pin 2): Open-Drain Charge Status Output. The charge status indicator pin has three states: pull-down, pulse at 2Hz and high impedance state. This output can be used as a logic interface or ...
Page 7
SIMPLIFIED BLOCK DIAGRAM – TOO COLD NOM + NTC 5 C2 TOO – HOT R NTC R9 + NTC_EN C3 – R10 PROG 0.1V + – C/10 CHRG 2 2.9V OPERATION ...
Page 8
LTC4069-4.4 OPERATION temperatures for a given application with the assurance that the charger will automatically reduce the current in worst-case conditions. The charge cycle begins when the voltage at the V rises above 3.5V and approximately 80mV above the BAT ...
Page 9
OPERATION battery voltage does not exceed the recharge threshold voltage when the timer ends, the timer resets and a 2.25 hour recharge cycle begins. The CHRG output assumes a strong pull-down state during recharge cycles until C/10 is reached when ...
Page 10
LTC4069-4.4 OPERATION POWER ON TRICKLE CHARGE MODE 1/10 FULL CHARGE CURRENT CHRG STRONG PULL-DOWN 1/4 CHARGE CYCLE (1.125 HOURS) DEFECTIVE BATTERY IS V < 2.9V? BAT BAD BATTERY MODE NO CHARGE CURRENT CHRG PULSES (2Hz) V < straight ...
Page 11
OPERATION APPLICATIONS INFORMATION Undervoltage Charge Current Limiting (UVCL) The LTC4069-4.4 includes undervoltage charge (ΔV current limiting that prevents full charge current until the input supply voltage exceeds approximately 220mV above the battery voltage. This feature is particularly useful if the ...
Page 12
LTC4069-4.4 APPLICATIONS INFORMATION a programmed current higher than 600mA. Since the LTC4069-4.4 will demand a charge current higher than the current limit of the input supply, the supply voltage will drop to the battery voltage plus 600mA times the on- ...
Page 13
APPLICATIONS INFORMATION Power Dissipation The conditions that cause the LTC4069-4.4 to reduce charge current through thermal feedback can be approximated by considering the power dissipated in the IC. For high charge currents, the LTC4069-4.4 power dissipation is approximately ...
Page 14
LTC4069-4.4 APPLICATIONS INFORMATION NOM 8.87k – 0.76 • NTC + 6 R1 604Ω – R NTC 10k + 0.35 • – 0.016 • Figure 6. NTC Circuits Thermistors The LTC4069-4.4 ...
Page 15
• 816 0 − COLD HOT NOM 3 266 0 5325 . . 3 266 0 5325 . − the ...
Page 16
LTC4069-4.4 RELATED PARTS PART NUMBER DESCRIPTION Battery Chargers LTC1734 Lithium-Ion Linear Battery Charger in ThinSOT LTC1734L Lithium-Ion Linear Battery Charger in ThinSOT LTC4002 Switch Mode Lithium-Ion Battery Charger LTC4050 Lithium-Ion Linear Battery Charger Controller LTC4052 Monolithic Lithium-Ion Battery Pulse Charger ...