LTC4059 LINER [Linear Technology], LTC4059 Datasheet - Page 7
![no-image](/images/no-image-200.jpg)
LTC4059
Manufacturer Part Number
LTC4059
Description
Manufacturer
LINER [Linear Technology]
Datasheet
1.LTC4059.pdf
(12 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC4059AEDC
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
LTC4059AEDC
Manufacturer:
LINEAR
Quantity:
2
Company:
Part Number:
LTC4059EDC
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
LTC4059EDC
Manufacturer:
LINEAR
Quantity:
5
OPERATIO
APPLICATIO S I FOR ATIO
The LTC4059/LTC4059A are linear battery chargers de-
signed primarily for charging single cell lithium-ion bat-
teries. Featuring an internal P-channel power MOSFET,
the chargers use a constant-current/constant-voltage
charge algorithm with programmable current. Charge
current can be programmed up to 900mA with a final float
voltage accuracy of 0.6%. No blocking diode or external
sense resistor is required; thus, the basic charger circuit
requires only two external components. The ACPR pin
(LTC4059A) monitors the status of the input voltage with
an open-drain output. The Li CC pin (LTC4059) disables
constant-voltage operation and turns the LTC4059 into a
precision current source capable of charging Nickel chem-
istry batteries. Furthermore, the LTC4059/LTC4059A are
designed to operate from a USB power source.
An internal thermal limit reduces the programmed charge
current if the die temperature attempts to rise above a
preset value of approximately 115 C. This feature protects
the LTC4059/LTC4059A from excessive temperature, and
allows the user to push the limits of the power handling
capability of a given circuit board without risk of damaging
the LTC4059/LTC4059A or external components. Another
Programming Charge Current
The charge current is programmed using a single resistor
from the PROG pin to ground. The battery charge current
is 1000 times the current out of the PROG pin. The
program resistor and the charge current are calculated
using the following equations:
For best stability over temperature and time, 1% metal-
film resistors are recommended.
The charge current out of the BAT pin can be determined
at any time by monitoring the PROG pin voltage and using
the following equation:
R
I
BAT
PROG
R
V
PROG
PROG
1000
U
• 1000
•
U
1 21
I
CHG
.
V
U
,
I
CHG
W
1000
•
R
1 21
PROG
.
U
V
benefit of the thermal limit is that charge current can be set
according to typical, not worst-case, ambient tempera-
tures for a given application with the assurance that the
charger will automatically reduce the current in worst-
case conditions.
The charge cycle begins when the voltage at the V
rises approximately 150mV above the BAT pin voltage, a
program resistor is connected from the PROG pin to
ground, and the EN pin is pulled below the shutdown
threshold (typically 0.85V).
If the BAT pin voltage is below 4.2V, or the Li CC pin is
pulled above V
charge the battery with the programmed current. This is
constant-current mode. When the BAT pin approaches the
final float voltage (4.2V), the LTC4059 enters constant-
voltage mode and the charge current begins to decrease.
To terminate the charge cycle the EN should be pulled
above the shutdown threshold. Alternatively, reducing the
input voltage below the BAT pin voltage will also terminate
the charge cycle.
Undervoltage Lockout (UVLO)
An internal undervoltage lockout circuit monitors the input
voltage and keeps the charger in undervoltage lockout until
V
The UVLO circuit has a built-in hysteresis of 115mV. If the
BAT pin voltage is below approximately 2.75V, then the
charger will remain in undervoltage lockout until V
above approximately 3V. During undervoltage lockout
conditions, maximum battery drain current is 4 A.
Power Supply Status Indicator
(ACPR, LTC4059A Only)
The power supply status output has two states: pull-down
and high impedance. The pull-down state indicates that
V
Undervoltage Lockout). When this condition is not met,
the ACPR pin is high impedance indicating that the
LTC4059A is unable to charge the battery.
CC
CC
rises approximately 150mV above the BAT pin voltage.
is above the undervoltage lockout threshold (see
Li CC
LTC4059/LTC4059A
(LTC4059 only), the LTC4059 will
CC
CC
rises
4059fa
7
pin