DS2431X Dallas Semiconducotr, DS2431X Datasheet - Page 18

• Manufacturer Part Number: DS2431X
• Description: 1024-Bit 1-Wire EEPROM
• Manufacturer: Dallas Semiconducotr

1-Wire SIGNALING
The DS2431 requires strict protocols to ensure data integrity. The protocol consists of four types of signaling on
one line: Reset Sequence with Reset Pulse and Presence Pulse, Write-Zero, Write-One, and Read-Data. Except
for the Presence pulse, the bus master initiates all falling edges. The DS2431 can communicate at two different
speeds, standard speed, and Overdrive Speed. If not explicitly set into the Overdrive mode, the DS2431
communicates at standard speed. While in Overdrive Mode the fast timing applies to all waveforms.
To get from idle to active, the voltage on the 1-Wire line needs to fall from V
from active to idle, the voltage needs to rise from V
make this rise is seen in Figure 10 as ' ' and its duration depends on the pullup resistor (R
capacitance of the 1-Wire network attached. The voltage V
logical level, not triggering any events.
Figure 10 shows the initialization sequence required to begin any communication with the DS2431. A Reset Pulse
followed by a Presence Pulse indicates the DS2431 is ready to receive data, given the correct ROM and memory
function command. If the bus master uses slew-rate control on the falling edge, it must pull down the line for t
t
standard speed. If the DS2431 is in Overdrive Mode and t
Overdrive Mode.
Figure 10. Initialization Procedure: Reset and Presence Pulse
After the bus master has released the line it goes into receive mode. Now the 1-Wire bus is pulled to V
the pullup resistor, or in case of a DS2482-x00 or DS2480B driver, by active circuitry. When the threshold V
crossed, the DS2431 waits for t
presence pulse, the master must test the logical state of the 1-Wire line at t
The t
DS2431 is ready for data communication. In a mixed population network, t
480µs at standard speed and 48µs at Overdrive speed to accommodate other 1-Wire devices.
Read-/Write-Time Slots
Data communication with the DS2431 takes place in time slots, which carry a single bit each. Write-time slots
transport data from bus master to slave. Read-time slots transfer data from slave to master. Figure 11 illustrates
the definitions of the write- and read-time slots.
All communication begins with the master pulling the data line low. As the voltage on the 1-Wire line falls below the
threshold V
a write-time slot and how long data is valid during a read-time slot.
F
to compensate for the edge. A t
RSTH
window must be at least the sum of t
V
TL
IHMASTER
, the DS2431 starts its internal timing generator that determines when the data line is sampled during
V
V
ILMAX
V
V
PUP
0V
TH
TL
t
F
RESISTOR
MASTER TX “RESET PULSE” MASTER RX “PRESENCE PULSE”
PDH
RSTL
and then transmits a Presence Pulse by pulling the line low for t
duration of 480µs or longer exits the Overdrive Mode, returning the device to
t
RSTL
PDHMAX
ILMAX
18 of 23
, t
past the threshold V
MASTER
PDLMAX
ILMAX
RSTL
, and t
t
PDH
is relevant for the DS2431 when determining a
is no longer than 80µs. the device remains in
RECMIN
t
MSP
t
PDL
MSP
. Immediately after t
t
RSTH
RSTH
TH
.
PUP
DS2431: 1024-Bit, 1-Wire EEPROM
. The time it takes for the voltage to
should be extended to minimum
below the threshold V
DS2431
t
REC
RSTH
PUP
) used and the
PDL
is expired, the
. To detect a
PUP
TL
. To get
through
RSTL
TH
is
+